外文翻译-变速器设计

第一篇：外文翻译-变速器设计

汽车变速器设计

----------外文翻译

我们知道，汽车发动机在一定的转速下能够达到最好的状态，此时发出的功率比较大，燃油经济性也比较好。因此，我们希望发动机总是在最好的状态下工作。但是，汽车在使用的时候需要有不同的速度，这样就产生了矛盾。这个矛盾要通过变速器来解决。

汽车变速器的作用用一句话概括，就叫做变速变扭，即增速减扭或减速增扭。为什么减速可以增扭，而增速又要减扭呢？设发动机输出的功率不变，功率可以表示为 N = wT，其中w是转动的角速度，T是扭距。当N固定的时候，w与T是成反比的。所以增速必减扭，减速必增扭。汽车变速器齿轮传动就根据变速变扭的原理，分成各个档位对应不同的传动比，以适应不同的运行状况。

一般的手动变速器内设置输入轴、中间轴和输出轴，又称三轴式，另外还有倒档轴。三轴式是变速器的主体结构，输入轴的转速也就是发动机的转速，输出轴转速则是中间轴与输出轴之间不同齿轮啮合所产生的转速。不同的齿轮啮合就有不同的传动比，也就有了不同的转速。例如郑州日产ZN6481W2G型SUV车手动变速器，它的传动比分别是：1档3.704:１；2档2.202:1；3档1.414:1；4档1:1；5档（超速档）0.802:1。

当汽车启动司机选择1档时，拨叉将1/2档同步器向后接合1档齿轮并将它锁定输出轴上，动力经输入轴、中间轴和输出轴上的1档齿轮，1档齿轮带动输出轴，输出轴将动力传递到传动轴上（红色箭头）。典型1档变速齿轮传动比是3:1,也就是说输入轴转3圈，输出轴转1圈。

当汽车增速司机选择2档时，拨叉将1/2档同步器与1档分离后接合2档齿轮并锁定输出轴上，动力传递路线相似，所不同的是输出轴上的1档齿轮换成2档齿轮带动输出轴。典型2档变速齿轮传动比是2.2:1，输入轴转2.2圈，输出轴转1圈，比1档转速增加，扭矩降低。

当汽车加油增速司机选择3档时，拨叉使1/2档同步器回到空档位置，又使3/4档同步器移动直至将3档齿轮锁定在输出轴上，使动力可以从轴入轴—中间轴—输出轴上的3档变速齿轮，通过3档变速齿轮带动输出轴。典型3档传动比是1.7:1，输入轴转1.7圈，输出轴转1圈，是进一步的增速。

当汽车加油增速司机选择4档时，拨叉将3/4档同步器脱离3档齿轮直接与输入轴主动齿轮接合，动力直接从输入轴传递到输出轴，此时传动比1:1，即输出轴与输入轴转速一样。由于动力不经中间轴，又称直接档，该档传动比的传动效率最高。汽车多数运行时间都用直接档以达到最好的燃油经济性。

换档时要先进入空档，变速器处于空档时变速齿轮没有锁定在输出轴上，它们不能带动输出轴转动，没有动力输出。

一般汽车手动变速器传动比主要分上述1－4档，通常设计者首先确定最低（1档）与最高（4档）传动比后，中间各档传动比一般按等比级数分配。另外，还有倒档和超速档，超速档又称为5档。

当汽车要加速超过同向汽车时司机选择5档，典型5档传动比是0.87:1，也就是用大齿轮带动小齿轮，当主动齿轮转0.87圈时，被动齿轮已经转完1圈了。

倒档时输出轴要向相反方向旋转。如果一对齿轮啮合时大家反向旋转，中间加上一个齿轮就会变成同向旋转。利用这个原理，倒档就要添加一个齿轮做“媒介”，将轴的转动方向调转，因此就有了一根倒档轴。倒档轴独立装在变速器壳内，与中间轴平行，当轴上齿轮分别与中间轴齿轮和输出轴齿轮啮合时，输出

轴转向会相反。

通常倒档用的同步器也控制5档的接合，所以5档与倒档位置是在同一侧的。由于有中间齿轮，一般变速器倒档传动比大于1档传动比，增扭大，有些汽车遇到陡坡用前进档上不去就用倒档开上去。

从驾驶平顺性考虑，变速器档位越多越好，档位多相邻档间的传动比的比值变化小，换档容易而且平顺。但档位多的缺点就是变速器构造复杂，体积大，现在轻型汽车变速器一般是4－5档。同时，变速器传动比都不是整数，而是都带小数点的，这是因为啮合齿轮的齿数不是整倍数所致，两齿轮齿数是整倍数就会导致两齿轮啮合面磨损不均匀，使得轮齿表面质量产生较大的差异。

手动变速器与同步器

手动变速器是最常见的变速器，简称MT。它的基本构造用一句话概括，就是两轴一中轴，即指输入轴、轴出轴和中间轴，它们构成了变速器的主体，当然还有一根倒档轴。手动变速器又称手动齿轮式变速器，含有可以在轴向滑动的齿轮，通过不同齿轮的啮合达到变速变扭目的。典型的手动变速器结构及原理如下。

输入轴也称第一轴，它的前端花键直接与离合器从动盘的花键套配合，从而传递由发动机过来的扭矩。第一轴上的齿轮与中间轴齿轮常啮合，只要轴入轴一转，中间轴及其上的齿轮也随之转动。中间轴也称副轴，轴上固连多个大小不等的齿轮。输出轴又称第二轴，轴上套有各前进档齿轮，可随时在操纵装置的作用下与中间轴的对应齿轮啮合，从而改变本身的转速及扭矩。输出轴的尾端有花键与传动轴相联，通过传动轴将扭矩传送到驱动桥减速器。

由此可知，变速器前进档位的驱动路径是：输入轴常啮齿轮－中间轴常啮齿轮－中间轴对应齿轮－第二轴对应齿轮。倒车轴上的齿轮也可以由操纵装置拨动，在轴上移动，与中间轴齿轮和输出轴齿轮啮合,以相反的旋转方向输出。

多数汽车都有5个前进档和一个倒档，每个档位有一定的传动比，多数档位传动比大于1，第4档传动比为1，称为直接档，而传动比小于1的第5档称为加速档。空档时输出轴的齿轮处于非啮合位置，无法接受动力传输。

由于变速器输入轴与输出轴以各自的速度旋转，变换档位时合存在一个“同步”问题。两个旋转速度不一样齿轮强行啮合必然会发生冲击碰撞，损坏齿轮。因此，旧式变速器的换档要采用“两脚离合”的方式，升档在空档位置停留片刻，减档要在空档位置加油门，以减少齿轮的转速差。但这个操作比较复杂，难以掌握精确。因此设计师创造出“同步器”，通过同步器使将要啮合的齿轮达到一致的转速而顺利啮合。

目前全同步式变速器上采用的是惯性同步器，它主要由接合套、同步锁环等组成，它的特点是依靠摩擦作用实现同步。接合套、同步锁环和待接合齿轮的齿圈上均有倒角（锁止角），同步锁环的内锥面与待接合齿轮齿圈外锥面接触产生摩擦。锁止角与锥面在设计时已作了适当选择，锥面摩擦使得待啮合的齿套与齿圈迅速同步，同时又会产生一种锁止作用，防止齿轮在同步前进行啮合。当同步锁环内锥面与待接合齿轮齿圈外锥面接触后，在摩擦力矩的作用下齿轮转速迅速降低（或升高）到与同步锁环转速相等，两者同步旋转，齿轮相对于同步锁环的转

速为零，因而惯性力矩也同时消失，这时在作用力的推动下，接合套不受阻碍地与同步锁环齿圈接合，并进一步与待接合齿轮的齿圈接合而完成换档过程

自动变速器

自动变速器的选挡杆相当于手动变速器的变速杆，一般有以下几个挡位：P(停车)、R(倒挡)、N(空挡)、D(前进)、S(or2，即为2速挡)、L(or1，即为1速挡)。这几个挡位的正确使用对于驾驶自动变速器汽车的人来说尤其重要，下面就让我们一起来熟悉一下自动变速器各挡位的使用要领。



●P(停车挡)的使用

发动机运转时只要选挡杆在行驶位置上，自动变速器汽车就很容易地行走。而停放时，选挡杆必须扳入P位，从而通过变速器内部的停车制动装置将输出轴锁住，并拉紧手制动，防止汽车移动。



●R(倒挡)的使用

R位为倒挡，使用中要切记，自动变速器汽车不像手动变速器汽车那样能够使用半联动，故在倒车时要特别注意加速踏板的控制。



●N(空挡)的使用

N位相当于空挡，可在起动时或拖车时使用。在等待信号或堵车时常常将选挡杆保持在D位，同时踩下制动。若时间很短，这样做是允许的，但若停止时间长时最好换入N位，并拉紧手制动。因为选挡杆在行驶位置上，自动变速器汽车一般都有微弱的行驶趋势，长时间踩住制动等于强行制止这种趋势，使得变速器油温升高，油液容易变质。尤其在空调器工作、发动机怠速较高的情况下更为不利。有些驾驶员为了节油，在高速行驶或下坡时将选挡杆扳到N位滑行，这很容易烧坏变速器，因为这时变速器输出轴转速很高，而发动机却在怠速运转，油泵供油不足，润滑状况恶化，易烧坏变速器。



●D(前进挡)的使用

正常行驶时将选挡杆放在D位，汽车可在1～4挡(或3挡)之间自动换挡。D位是最常用的行驶位置。需要掌握的是：由于自动变速器是根据油门大小与车速高低来确定挡位的，所以加速踏板操作方法不同，换挡时的车速也不相同。如果起步时迅速将加速踏板踩下，升挡晚，加速能力强，到一定车速后，再将加速踏板很快松开，汽车就能立即升挡，这样发动机噪声小，舒适性好。

D位的另一个特点是强制低挡，便于高速时超车，在D位行驶中迅速将加速踏板踩到底，接通强制低挡开关就能自动减挡，汽车很快加速，超车之后松

开加速踏板又可自动升挡。



●S、L位低挡的使用

自动变速器在S位或L位上处于低挡范围，可以在坡道等情况下使用。下坡时换入S位或L位能充分利用发动机制动，避免车轮制动器过热，导致制动效能下降。但是从D位换入S位或L位时，车速不能高于相应的升挡车速，否则发动机会强烈振动，使变速器油温急剧上升，甚至会损坏变速器。



另外在雨雾天气时，若路面附着条件差，可以换入S位或L位，固定在某一低挡行驶，不要使用能自动换挡的位置，以免汽车打滑。同时必须牢记，打滑时可将选挡杆推入N位，切断发动机的动力，以保证行车安全。

原文：

Transmission design

As we all know,automobile engine to a certain speed can be achieved under the best conditions, when compared issued by the power, fuel economy is relatively good.Therefore, we hope that the engine is always in the best of conditions to work under.However, the use of motor vehicles need to have different speeds, thus creating a conflict.Transmission through this conflict to resolve.Automotive Transmission role sum up in one sentence, called variable speed twisting, twisting or slow down the growth rate by increasing torsional.Why can slow down by twisting, and the growth rate but also by twisting? For the same engine power output, power can be expressed as N = wT, where w is the angular velocity of rotation, and T Niuju.When N fixed, w and T is inversely proportional to the.Therefore, the growth rate will reduce twisting, twisting slowdown will increase.Automotive Transmission speed gear based on the principle of variable twisted into various stalls of different transmission ratio corresponding to adapt to different operational conditions.General to set up a manual gearbox input shaft, intermediate shaft and output shaft, also known as the three-axis, as well as Daodang axis.Three-axis is the main transmission structure, input shaft speed is the speed of the engine, the output shaft speed is the intermediate shaft and output shaft gear meshing between different from the speed.Different gears are different transmission ratio, and will have a different speed.For example Zhengzhourichan ZN6481W2G manual transmission car-SUV, its transmission ratio are: 1 File 3.704:1;stalls 2.202:1;stalls 1.414:1;stalls 1:1 5 stalls(speeding file)0.802: 1.When drivers choose a launch vehicle stalls, Plectrum will be 1 / 2 file synchronization engagement with a back stall gear and output shaft lock it, the power input shaft, intermediate shaft and output shaft gear of a stall, a stall the output shaft gear driven, and the output shaft power will be transmitted to the drive shaft(red arrow).A typical stall Biansuchilun transmission ratio is 3:1, that is to say three laps to the input shaft and output shaft to a circle.When the growth rate of car drivers choose two stalls, Plectrum will be 1 / 2-file synchronization and file a joint separation after 2 stall and lock the output shaft gear, power transmission line similar, the difference is that the output shaft gear of a stall 2 stall replaced by the output shaft gear driven.2 stall Biansuchilun typical transmission ratio is 2.2:1, 2.2 laps to the input shaft and output shaft to a circle than a stall speed increase, lower torque.When refueling vehicle drivers growth stalls option 3, Plectrum to 1 / 2 back to the free file-synchronization position, and also allows the 3 / 4 file synchronization Mobile stall until 3 in the output shaft gear lock, power can be into the shaft axisthe output shaft of the three stalls Biansuchilun, led through three stalls Biansuchilun output shaft.3 stalls typical transmission ratio is 1.7:1, 1.7 laps to the input shaft and output shaft to a circle is further growth.When car drivers Option 4 refueling growth stalls, Plectrum will be 3 / 4 from the 3-file synchronization stall gear directly with the input shaft gear joint initiative, and power transmission directly from the input shaft to the output shaft, the transmission ratio at 1:1, that the input shaft and output shaft speed the same.The driving force without intermediate shaft, also known as direct file, the file transmission than the

maximum transmission efficiency.Most cars run-time files are used directly to achieve the best fuel economy.Shift into the first interval when, in a free transmission when Biansuchilun output shaft is not locked in, they can not rotate the output shaft driven, not power output.General automotive manual transmission than the main 1-4 stalls, usually the first designers to determine the minimum(one stall)and maximum(4 files)transmission ratio, the middle stall drive by geometric progression than the general distribution.In addition, there are stalls Daodang and speeding, speeding file is also known as the five stalls.When the car to accelerate to more than car drivers with the choice of five stalls, and a typical five-transmission ratio is 0.87:1, which is driven by a pinion gear, the gear when the initiative to 0.87 zone, passive gear have been transferred to a circle of the End.Dao Dang, the opposite direction to the output shaft rotation.If one pair of meshing gears when we reverse rotation, with a middle gear, it will become the same to the rotation.Use of this principle, we should add a gear Daodang the “media” will be rotational direction reversed, it will have a Daodang axis.Daodang installed in the transmission shaft independent crust, and the intermediate shaft parallel axis gear with the intermediate shaft and output shaft gear meshing gears, will be contrary to the output shaft.Daodang usually used for the synchronization control also joins five stalls, stalls and Daodang 5 position in the same side.As a middle gear, the general transmission Daodang transmission ratio greater than 1 file transmission ratio, by twisting, steep slope with some vehicles encountered on the progress stalls falters with a Daodang boost.Ride from the driver of the considerations, better transmission stall, stall adjacent stall more than the transmission changes the ratio of small, and easy to shift smoothly.However, the shortcomings of the stalls is more transmission structure is complicated, bulky, light vehicle transmission is generally 4-5 stalls.At the same time, transmission ratio is not integral, but with all of the decimal point, it is because of the gear teeth meshing is not caused by the whole multiples of two gear teeth can lead to the whole multiples of two meshing gears of uneven wear, making the tooth surface quality have a greater difference.Manual transmission and synchronizer

Manual transmission is the most common transmission, or MT.Its basic structure sum up in one sentence, is a two-axle shaft, where input shaft, the shaft axis and intermediate shaft, which constitute the main body of the transmission and, of course, a Daodang axis.Manual transmission known as manual gear transmission, which can be in the axial sliding gears, the gears meshing different variable speed reached twisting purpose.Typical manual transmission structure and principles are as follows.Input shaft also said that the first axis, and its front-end Spline driven directly with the clutch disc sets with the Spline, by the transfer of torque from the engine.The first axis of the intermediate shaft and gears meshing gears often, as long as the shaft axis to a turn, the intermediate shaft and gear also will be rotating.Vice also said intermediate shaft axis, the axis-even more than the size gear.Also known as the second output shaft axis, the axis of various sets of gear stall progress can be manipulated at any time in the

role of the device and the corresponding intermediate shaft gear meshing, thus changing its speed and torque.With the end of the output shaft spline associated with the drive shaft through the drive shaft torque transmitted to the drive axle reducer.Thus, progress stalls drive transmission path is: input shaft gear often rodentscorresponding intermediate shaft gear-the second axis corresponding gear.Reversing the gear shaft can be manipulated by the device pick in the axis movement, and the intermediate shaft and output shaft gear meshing gears, to the contrary to the direction of rotation output.Most cars have five stalls and a Daodang forward, a certain degree of each stall transmission ratio, the majority of stalls transmission ratio greater than 1, 4 file transmission ratio of 1, known as direct stalls, and transmission ratio is less than 1 No.5 stall called accelerated stall.Free at the output shaft gear in a position of non-engagement, unacceptable power transmission.The transmission input shaft and output shaft rotational speed to their own, transform a stall when there is a “synchronous”.Two different rotational speed gear meshing force will impact the collision occurred, damage gear.Therefore, the old transmission shift to a “feet-off” approach, or stall on the location of the free stay for a while by stalls in the free position refueling doors, in order to reduce the speed differential gear.However, this operation is relatively more complicated and difficult to grasp accurate.So designers create a “synchronized,” and allows synchronization through the meshing of gears to be consistent speed and smooth meshing.At present Synchronous Transmission is based on the synchronization of inertia, mainly from joint sets, synchronous lock ring, and so on, it is characterized by friction on the role of synchronization.Splice sets Genlock engagement ring gear and the ring gear when it had Chamfer(Lock angle), Genlock within the cone ring gear engagement with the question of cone ring gear contact friction.Lock and cone angle has been made in the design of an appropriate choice to be made friction cone of the teeth meshing with the ring gear quickly sets pace at the same time will have a Lock role and to prevent the gears meshing in sync before.When synchronization lock cone ring gear engagement with the question of cone ring gear after contact in the effects of friction torque gear speed quickly lower(or higher)with the same speed synchronous lock ring, the two synchronous rotation of the gear Genlock Central zero speed, thus moment of inertia also disappear, then in force under the impetus of engagement sets unhindered and synchronization lock ring gear engagement, and further engagement with the question of gear engagement and the completion Gear Shift Process.The automatic gearbox The automatic gearbox chooses to block the pole the equal to moving the stick shift of the gearbox, having generally below several blocks:P(parking), R(pour to block), N(get empty to block), D(go forward), S(or2, namely for 2 block soon), L.(or1, namely for 1 block soon)This several an usage for blocking a right usages coming driver the automatic gearbox is automotive of person to say particularly important, underneath let us very much familiar with once automatic gearbox eachly blockings main theme.The usage of the P(the parking blocks)The launches the luck turns as long as choose to block the pole in driving the position, automatic gearbox car run about very easily.But park, choose to block the pole

must pull into of P, from but pass the internal parking system in gearbox moves the device will output the stalk lock lives, combining to tense the hand system move, preventing the car ambulation.The usage of the R(pour to block)R a control for is pouring blocking, using inside wanting slicing recording, automatic gearbox car unlike moving gearbox car so can using half moving, so while reversing the car wanting special attention accelerating pedal.The usage of the N(get empty to block)The N is equal to get empty to block, can while starting or hour of trailer usage.At wait for the signal or block up the car will often often choose to block the pole keeps in the of D, trampling at the same time the next system move.If time is very short, do like this is an admission of, but if stop the time long time had better change into of N, combine to tense the hand system moves.Because choose to block the pole in driving the position, the automatic gearbox car has generally and all to drive the trend faintly, long hours trample the system move same as a deterrent this kind of trend, make gearbox oil gone up, the oil liquid changes in character easily.Particularly in the air condition machine work, launch the soon higher circumstance in machine bottom more disadvantageous.Some pilots for the sake of stanza oil, at made good time or go down slope will choose to block the pole pull the of N skids, this burn the bad gearbox very easily, launching the machine to revolves soon in the however because the gearbox outputs at this time the stalk turns soon very high， the oil pump provides the oil shortage, lubricating the condition worsen, burn the bad gearbox easily.

The usage of the D(go forward to block)Will choose to block when is normal to drive the pole put in the of D, car can at 1 ～ 4 block(or 3 block)its change to block automatically.The of D drives the position most in common usely.What demand control is:Because the automatic gearbox is soon high and low with car to come to make sure to block according to the accelerator size a, so accelerate the pedal operation method is different, changing to block the hour of the car is soon too not same alike.If start hour quick accelerate the pedal tramples the bottom, rising to block the night, accelerating the ability is strong, arriving certain car soon behind, then will accelerate the pedal loosen to open very quickly, car can rise to block immediately, launch like this the machine voice is small, comfortable good.The another characteristics of the D is a compulsory low blocking, easy to high speed the hour overtakes a car, will accelerate quickly in of D drove the pedal trample after all, connect the compulsory low fend off the pass and then can reduce to block automatically, the car accelerates very quickly, after overtaking a car loosen to open the pedal of acceleration to can rise to block automatically again.The usage of the S, of L low the usage that block The automatic gearbox in in is placed in the low blocking the scope on of S or of Ls, can usage under an etc.circumstance.It change to can make use of to launch well into of S or of Ls the mechanism move, avoiding the car wheel system move the machine over hot, cause the system move the effect descent while going down slope.But change into from the of D of S or of L, car soon can't higher than rise to block the car homologously soon, otherwise strong vibration in opportunity to launch, make gearbox oil hoicked, even will damage the gearbox.The is another at rain fog weather hour, if the road adheres to the term bad, can change into a position for or of L, fixing at somely first lowly blocking driving, doing not use can automatically changing blocking, in order to prevent the car beats slippery.Must keep firmly in mind at the same time, beat the slippery hour can will choose to block the pole pushes into a motive for, cutting off launching machine, toing guarantee a car the safety.

第二篇：变速器设计-外文翻译

Dynamic Modeling of Vehicle Gearbox for Early Detection of Localized Tooth Defect

Helwan University ABSTRACT Dynamic modeling of the gear vibration is a useful tool to study the vibration response of a geared system under various gear parameters and operating conditions.An improved understanding of vibration signal is required for early detection of incipient gear failure to achieve high reliability.However, the aim of this work is to make use of a 6-degree-of-freedom gear dynamic model including localized tooth defect for early detection of gear failure.The model consists of a gear pair, two shafts, two inertias representing load and prime mover and bearings.The model incorporates the effects of time-varying mesh stiffness and damping, backlash, excitation due to gear errors and modifications.The results indicate that the simulated signal shows that as the defect size increases the amplitude of the acceleration signal increases.The crest factor and kurtosis values of the simulated signal increase as the fault increases.Though the crest factor and kurtosis values give similar trends, kurtosis is a better indicator as compared to crest factor.KEYWORDS：Vibration acceleration, system modeling, Crest Factor, Kurtosis value, defect size, gear meshing, pinion, gear NOMENCLATURE JD，J1，J2，JL

Drive motor, pinion, gear, and load mass moment of inertia

Nagwa Abd-elhalim, Nabil Hammed, Magdy Abdel-hady，Shawki Abouel-Seoud and Eid S.Mohamed

replacement decision in a suitable time.m1，mMasses of pinion and gear.TD

Driving motor torque.TL

Load torque.第 1 页

共 7 页

TF1，TFFriction torque.C1，C2

Viscous damping coefficient of pinion and gear bearing.Cm

Gear mesh damping.Gear mesh stiffness.Km

K1，K2

Pinion and gear shaft stiffness.4

The variance square.N

The number of samples.f

The defect width in face direction.Unit width Hertzian stiffness.KhD，1，2，L Angular displacement of drive motor, pinion, gear and load.D，1，2，L Angular velocity of drive motor, pinion, gear and load.，，， Angular acceleration of drive motor, pinion, gear and load.D12LINTRODUCTION Much of the past research in the dynamic modeling area has concluded that an essential solution to the problem is to use a comprehensive computer modeling and simulation tool to aid the transmission design and experiments.These have been two major obstacles to such an approach:(1)Progress in understanding of the basic gear rattle phenomenon has been limited and slow.This is because the engine-clutch-transmission system involves some strong nonlinearities including gear backlash, multi-valued springs, dry friction, hysteresis, and the like.(2)The gear rattle is a system problem and not only problem of gear teeth.Even through the research and industrial community has discussed the difficulties in varies stages of the problem, yet no thorough frame work covering the entire investigation process of such problem currently exists.This is largely due o the complexity of the power train system, which

第 2 页

共 7 页

may make a computer analysis tool inefficient, in particularly when many different elements and clearances are encountered(e.g., gears, bearings, splines, synchronizers, and clutch)[1-3].A comprehensive review of mathematical models used in gear dynamics, published before 1986, has been presented by [4].In this review, gear dynamic models without defects have been discussed.In the past few years, researchers have been working on the gear dynamic models which include defects like pitting, spalling, crack and broken tooth.A single-degree-of-freedom model is used which include the e4ffects of variable mesh stiffness, damping, gear errors, profile modifications and backlash.The effect of time-varying meshing damping is also included in this case, The solution is obtained by using the harmonic balance methods.A method of calculated the optimum profile modification has been proposed in order to obtain a zero vibration of the gear pair [5-7].They also proposed a linear approximate equation to mode the gear pair by using a single-degree-of freedom model Gear rattle vibration is a undesirable vibration for passenger cars and light trucks equipped with manual transmissions.Unlike automatic transmissions, manual transmission do not have the high viscous damping inherent to a hydrodynamic torque converter to suppress the impacting of gear teeth oscillating through their gear backlash.Therefore a significant level of vibration an be produced by the gear rattle and transmitted both inside the passenger compartment and outside the vehicle.Gear rattle, idle shake, and other vibration generated in the automobile driveline have become an important concern to automobile manufactures in their pursuit of an increased level of perception of high vibration quality.The torsional vibration o driveline is a major source of gear rattle vibration.The manual transmission produces gear rattle by the impacting of gear oscillating through their gear backlash.The impact collisions are transmitted to the transmission housing via shafts and bearings [8].The gear pair dynamic models including defects have been done by [9].The study

第 3 页

共 7 页

suggests that little work has been done on modeling of gear vibration with defect and an accurate analytical procedure to predict gear vibrations in the presence of local tooth fault has yet to be developed.However, the purpose of this paper is to develop a multidegree-of-freedom nonlinear model for a gear pair that can be used to study the effect of lateral-torsional vibration coupling on vibration response in the presence of localized tooth defect.A typical fault signal is assumed to be impulsive in nature because of the way it is generated.The simulation artificially introduced pitting in gears in multi-stage automotive transmission gearbox at different operation conditions(load, speed, etc).The processing of simulated and experimental signals is also introduced.SIGNAL-PROCESSING TECHNIQUE Among various signal-processing techniques, crest factor and kurtosis analysis have been used for analyzing the whole vibration signal for the early detection of fault.In this section, crest factor and kurtosis value have been explained.MATHEMATICAL MODEL FORMULATION

Helical gears are almost always used in automotive transmissions.The meshing stiffness of a helical tooth pair is time-varying [10], and was modeled as a series of suggested spur gears so that the simulation techniques for spur gears can be applied.where M is Module(mm), b is Face width(mm),  is pressure angle(deg),  is helix angle(deg)and D1 is pitch diameter(mm).Fig.2 shows the equivalent gear system in the first gear-shift, where the main parameters for the gear system of Fiat-131 gearbox and the equivalent gear system in the first gear-shift are also shown in the figures.第 4 页

共 7 页

汽车变速箱动态建模轮齿局部缺陷的早期检测

Nagwa Abd-elhalim, Nabil Hammed, Magdy Abdel-hady，Shawki Abouel-Seoud and Eid S.Mohamed

阿勒旺大学

摘要

在研究齿轮系统中各种齿轮参数的振动响应和操作条件时，齿轮振动的动态建模是一个非常有用的工具。对早期的齿轮检测提出了一种改进理解的振动信号，但还没达到高的可靠性。但是，这项工作的目的是利用一个6自由度的齿轮动力学模型对齿轮轮齿缺陷故障的早期检测。该模型包括一对齿轮副、两个轴、两个惯性负载、动力传动装置和轴承。由于齿轮的误差和变动，该模型被采用时受到时变啮合刚度、阻尼、反弹和励磁的影响。模拟信号显示的结果表明，随着缺陷尺寸的增加加速度信号的振幅增加。模拟信号的波峰因素和峰值随着缺陷的增加而增加。虽然波峰因素和峰值做同样的趋势，但和波峰因素相比峰值是一个比较好的指标。关键词：振动加速度、系统建模、波峰因素、峰值、缺陷大小、齿轮啮合、齿轮 专业术语

JD，J1，J2，JL

驱动电机、小齿轮、大齿轮和负载在一定时间内的惯性矩 m1，m

1大齿轮、小齿轮的模数 TD

发动机驱动转矩 TL

负载力矩 TF1，TF摩擦力矩

C1，C2

齿轮、轴承的粘滞阻尼系数

Cm

齿轮啮合阻尼

齿轮啮合刚度 Km

K1，K齿轮、齿轮轴的刚度



平方差

第 5 页

共 7 页 4

N

样本数量

f

宽度方向的缺陷

单位宽度的刚度 KhD，1，2，L

驱动电机、小齿轮、大齿轮和负载的角位移 D，1，2，L

驱动电机、小齿轮、大齿轮和负载的角速度

，，，

驱动电机、小齿轮、大齿轮和负载的角加速度 D12L引言

在大多数过去的动态建模研究领域中，解决问题的重要办法是全面使用计算机建模和仿真工具来辅助变速器的设计和实验。这种方法有两种主要的障碍：（1）对齿轮传动中噪声基本认识的进展是有限的和缓慢的。这是因为发动机离合器传动系统中包括齿轮侧隙、多值弹簧、非线性滞后等等。（2）齿轮发出的噪声是一个系统问题，并不是齿轮的唯一问题。既使是工业研究领域已经讨论了这个问题在不同阶段所出现的不同问题，但并没有彻底覆盖工作的框架，整个研究过程中的问题依然存在。这主要是由于列车电力系统的复杂性，可能导致你的计算机的分析工具效率不高，尤其是工作中遇到许多不同的因素和间隙（例如：齿轮、轴承、花键、同步器和离合器）。

在1986年出版之前，对齿轮动力学中提出的齿轮动态建模进行了审查。这次审查中，对不存在齿轮缺陷的齿轮动力学模型进行了讨论。在过去的几年里，研究人员对齿轮的动态模型缺陷进行了研究，其中包括点蚀、剥落、裂缝和齿轮折断等。

单自由度系统模型中，对啮合刚度的影响包括4个方面的因素，阻尼、齿轮误差、轮廓变动和齿侧间隙，时变啮合阻尼效应也包含在这种情况中。解决问题的方法是利用谐波平衡的方法。为了实现齿轮副的零振动，提出了一种最优化的计算方法。他们还利用齿轮副单自由度模型提出了一个近似的线性方程模型。

齿轮噪声振动是轿车和轻型货车手动变速箱中的不良振动。不同于自动变速箱的是，手动变速箱没有一个固有的高粘性阻尼液力变矩器以制止通过齿轮侧隙造成的齿轮摆动的影响。因此，无论是在车厢内外由齿轮振动和传动产生的噪声，对车

第 6 页

共 7 页

辆振动的影响都非常大。随着人们对汽车高性能振动的追求，齿轮松动、振动以及其他汽车传动系产生的噪声已成为人们关注的重点。传动系统中的扭转振动是齿轮振动的一种主要噪声来源。手动变速箱产生的齿轮噪声是由于齿轮受到齿轮间隙振动的影响。通过轴和轴承把碰撞产生的影响传输到变速箱壳体。

对齿轮副的动态模型缺陷的研究结果表明，对齿轮副动态模型缺陷已做了大量工作，用准确的分析方法对齿轮振动的检测在当时轮齿故障方面还没得到发展。然而，本研究的目的是建立一个多自由度非线性模型用于研究，结果表明轮齿局部缺陷的扭转振动是耦合振动的响应。由于他的产生一个典型的故障信号被假设为自然的脉冲信号。在不同操作条件下（负荷、转速等），模拟人工对多级汽车变速器齿轮缺陷进行了介绍。同时也对信号的仿真和实验处理进行了介绍。信号处理技术

在各种各样的信号处理技术中，波峰因素、峰值已用于分析整个振动信号的早期故障。在本节中，波峰因素和峰值已被解释。数学模型

汽车变速器中的齿轮大都是斜齿圆柱齿轮。被视为一系列齿轮仿真技术适用于螺旋状的轮齿时变啮合刚度。式中m是模数(毫米),b齿面宽(毫米),是压力角(度),是螺旋角(度)，D1是直径(毫米)。图2的数据显示了等效齿轮系统在齿轮变动中变速箱齿轮系统的主要参数。

第 7 页

共 7 页

第三篇：外文翻译

当今时代是一个自动化时代，交通灯控制等很多行业的设备都与计算机密切相关。因此，一个好的交通灯控制系统，将给道路拥挤，违章控制等方面给予技术革新。随着大规模集成电路及计算机技术的迅速发展，以及人工智能在控制技术方面的广泛运用，智能设备有了很大的发展，是现代科技发展的主流方向。本文介绍了一个智能交通的系统的设计。该智能交通灯控制系统可以实现的功能有：对某市区的四个主要交通路口进行控制：个路口有固定的工作周期，并且在道路拥挤时中控制中心能改变其周期：对路口违章的机动车能够即时拍照，并提取车牌号。在世界范围内，一个以微电子技术，计算机和通信技术为先导的，一信息技术和信息产业为中心的信息革命方兴未艾。而计算机技术怎样 与实际应用更有效的结合并有效的发挥其作用是科学界最热门的话题，也是当今计算机应用中空前活跃的领域。本文主要从单片机的应用上来实现十字路口交通灯智能化的管理，用以控制过往车辆的正常运作。

研究交通的目的是为了优化运输，人流以及货流。由于道路使用者的不断增加，现有资源和基础设施有限，智能交通控制将成为一个非常重要的课题。但是，智能交通控制的应用还存在局限性。例如避免交通拥堵被认为是对环境和经济都有利的，但改善交通流也可能导致需求增加。交通仿真有几个不同的模型。在研究中，我们着重于微观模型，该模型能模仿单独车辆的行为，从而模仿动态的车辆组。

由于低效率的交通控制，汽车在城市交通中都经历过长时间的行进。采用先进的传感器和智能优化算法来优化交通灯控制系统，将会是非常有益的。优化交通灯开关，增加道路容量和流量，可以防止交通堵塞，交通信号灯控制是一个复杂的优化问题和几种智能算法的融合，如模糊逻辑，进化算法，和聚类算法已经在使用，试图解决这一问题，本文提出一种基于多代理聚类算法控制交通信号灯。

在我们的方法中，聚类算法与道路使用者的价值函数是用来确定每个交通灯的最优决策的，这项决定是基于所有道路使用者站在交通路口累积投票，通过估计每辆车的好处(或收益)来确定绿灯时间增益值与总时间是有差异的，它希望在它往返的时候等待，如果灯是红色，或者灯是绿色。等待，直到车辆到达目的地，通过有聚类算法的基础设施，最后经过监测车的监测。

我们对自己的聚类算法模型和其它使用绿灯模拟器的系统做了比较。绿灯模拟器是一个交通模拟器，监控交通流量统计，如平均等待时间，并测试不同的交通灯控制器。结果表明，在拥挤的交通条件下，聚类控制器性能优于其它所有测试的非自适应控制器，我们也测试理论上的平均等待时间，用以选择车辆通过市区的道路，并表明，道路使用者采用合作学习的方法可避免交通瓶颈。

本文安排如下：第2部分叙述如何建立交通模型，预测交通情况和控制交通。第3部分是就相关问题得出结论。第4部分说明了现在正在进一步研究的事实，并介绍了我们的新思想。

The times is a automation times nowadays,traffic light waits for much the industey equipment to go hand in hand with the computer under the control of.Therefore,a good traffic light controls system,will give road aspect such as being crowded,controlling against rules to give a technical improvement.With the fact that the large-scale integrated circuit and the computer art promptness develop,as well as artificial intelligence broad in the field of control technique applies,intelligence equipment has had very big development,the main current being that modern science and technology develops direction.The main body of a book is designed having introduccd a intelligence traffic light systematically.The function being intelligence traffic light navar’s turn to be able to come true has：The crossing carries out supervisory control on four main traffic of some downtown area;Every crossing has the fixed duty period,charges centrefor being able to change it’s period and in depending on a road when being crowded;The motro vehicle breaking rules and regulations to the crossing is able to take a photo immediately,abstracts and the vehicle shop sign.Within world range ,one uses the microelectronics technology,the computer and the technology communicating by letter are a guide’s,centering on IT and IT industry information revolution is in the ascendant.But,how,computer art applies more effective union and there is an effect’s brought it’s effect into play with reality is the most popular topic of scientific community,is also that computer applications is hit by the unparalleled active field nowadays.The main body of a book is applied up mainly from slicing machine’s only realizing intellectualized administration of crossroads traffic light,use operation in controlling the vehicular traffic regularity.Transportation research has the goal to optimize transportation flow of people and goods.As the number of road users constantly increases, and resources provided by current infras-tructures are limited, intelligent control of traffic will become a very important issue in thefuture.However, some limitations to the usage of intelligent tra?c control exist.Avoidingtraffic jams for example is thought to be beneficial to both environment and economy, butimproved traffic-flow may also lead to an increase in demand [Levinson, 2003].There are several models for traffic simulation.In our research we focus on microscopicmodels that model the behavior of individual vehicles, and thereby can simulate dynam-ics of groups of vehicles.Research has shown that such models yield realistic behavior[Nagel and Schreckenberg, 1992, Wahle and Schreckenberg, 2001].Cars in urban traffic can experience long travel times due to inefficient traffic light con-trol.Optimal control of traffic lights using sophisticated sensors and intelligent optimizationalgorithms might therefore bevery beneficial.Optimization of traffic light switching increasesroad capacity and traffic flow, and can prevent tra?c congestions.Traffic light control is acomplex optimization problem and several intelligent algorithms, such as fuzzy logic, evo-lutionary algorithms, and reinforcement learning(RL)have already been used in attemptsto solve it.In this paper we describe a model-based, multi-agent reinforcement learningalgorithm for controlling traffic lights.In our approach, reinforcement learning [Sutton and Barto, 1998, Kaelbling et al., 1996]with road-user-based value functions [Wiering, 2000] is used to determine optimal decisionsfor each traffic light.The decision is based on a cumulative vote of all road users standingfor a traffic junction, where each car votes using its estimated advantage(or gain)of settingits light to green.The gain-value is the difference between the total time it expects to waitduring the rest of its trip if the light for which it is currently standing is red, and if it is green.The waiting time until cars arrive at their destination is estimated by monitoring cars flowingthrough the infrastructure and using reinforcement learning(RL)algorithms.We compare the performance of our model-based RL method to that of other controllersusing the Green Light District simulator(GLD).GLD is a traffic simulator that allows usto design arbitrary infrastructures and traffic patterns, monitor traffic flow statistics such asaverage waiting times, and test different traffic light controllers.The experimental resultsshow that in crowded traffic, the RL controllers outperform all other tested non-adaptivecontrollers.We also test the use of the learned average waiting times for choosing routes of cars through the city(co-learning), and show that by using co-learning road users can avoidbottlenecks.

第四篇：外文翻译

设计一个位于十字路口的智能交通灯控制系统

摘要：本文模型使用模糊本体的交通灯控制域，并把它应用到控制孤立十字路口。本文最重要的目的之一是提出一个独立的可重复使用的交通灯控制模块。通过这种方式，增加软件的独立性和为其他的软件开发活动如测试和维护，提供了便利。专家对本体论进行手动的开发和评估。此外，交通数据提取和分类路口使用的人工神经网络的图像处理算法。根据预定义的XML架构，这种信息转化为XML实例映射到适合使用模糊推理引擎的模糊规则的模糊本体。把本系统的性能与其他类似的系统性能进行比较。比较结果显示：在所有的交通条件下，在每个周期中，对每辆车它有低得多的平均延迟时间与其他的控制系统相比。

关键词:模糊本体,智能代理,智能交通系统(ITS),交通信号灯控制(TLC),孤立的十字路口,图像处理,人工神经网络

1.引言

作为城市交通增加的结果,道路网络的能力有限和发展交通工具和方法的技术方面，许多实体，关系，情况和规则已经进入交通灯控制域和转化成为一个知识领域。这个领域的建模知识帮助交通代理和应用有效地管理关于实时条件下的交通。全面知识建模领域的一个最合适的方法是使用本体概念。“本体论是一个正式的、明确的一个共享的概念化的规范。以前的模型是基本的本体建设的基础，为下列建立一个共享的语义丰富的知识域。除了本体作为概念化的形式主义的重要性，它有可能超过所代表的数据。这种能力将提高有关性能的决定和其他非智能系统的功能特点。在近年来，本体论上的研究正成为一个新的热点话题在不同的活动，如人工智能，知识管理，语义网络，电子商务和几个其他应用领域。这些领域之一是智能交通系统。一些努力已制成这个通过展示和使用本体检测交通领域拥塞，管理非城市道路气象事件，驾驶阿德福—索里系统，共享和整合一个智能交通系统。本文的目的是介绍一个红绿灯有效控制孤立交叉口这方面的知识重用的控制本体。这种新的办法适用于智能代理使用知识决策模糊。该系统采用的图像来自安装了监控摄像机拍摄的路口。这些图像处理利用图像处理算法和神经网络的方法，然后发送到一个智能代理。第2节中，我们将简要地解释了在这项工作中运用的技术包括seman-TIC网络技术，智能代理技术和交通的回地面光控制方法。在第3节，新的系统架构是基于分层语义网络架构。第4节介绍交通灯控制的模糊本体的建设。第五节从路口提取的图像信息解释。在第6节，智能系统的运作被完整描述，最后在第7节对所提出的方法进行评估，对结论进行阐述。

2.背景

本节说明在这项工作中的应用技术包括语义网络技术，特别本体和模糊本体。此外，国家的交通灯控制的艺术方法是简要介绍。2.1.语义网络技术

语义网络被定义为当前Wed的延伸，这些网站的信息都给出明确的含义;使电脑与人更好的合作。有几层语义Web的建议源自伯纳斯滞后阶段。在此类别中的所有规则如表1所示。图.4显示输出模式的示意图。本次评选有助于智能系统，以确定下一步的阶段测序。

另一种模糊的规则类别涉及估计优化周期时间。这些规则的模糊变量是天气条件，时间，每天平均车辆拥堵情况。出于这个原因，60个模糊规则被定义了。从气象研究所取得气象条件。日期和时间也是在交通专家的知识的基础上以模糊变量形式预先定义的。图5显示日期，时间和周期时间的隶属函数。当天的参数是在日历基础上基于假期和正常的一天与周期时间量的关系预定义的。例如，假期期间的周期时间是较平日少。因此，平日的隶属度比假期多。

例如一个阶段选型的模糊规则如下所述：“如果一个路口的类型是四的方式，平均车辆拥堵低，平均行人拥堵是中等，然后相类型是简单的两阶段”。此外，为周期时间估计的模糊规则表示如下：“如果天气条件是晴天，时间是早晨，天是正常的，平均车辆拥堵是低，则周期时间短”。在此类别中的所有规则都列在附录A。

在此步骤结束时，应该对交通灯逻辑控制的项目的有效性进行评估。此功能是使用专家的意见。评价过程的主要目的是显示发展的本体和其相关的软件环境的用处。虽然所有的信息，尤其是交通灯控制规则已提取国际标准和科学交通文学，专家的知识优势是他们最后的正确性验证标准。所有模糊规则，包括优化周期时间和相位类型的规则，在这个过程中，准备以调查问卷形式和展现给一些专家包括从德黑兰警察局交通上校和两名来自德黑兰的交通组织工程师。由于德尔菲专家的意见，约有84％的淘汰型规则和优化周期时间的87％被接受。此外，所有交通逻辑控制的元素包括概念，关系，属性和公理都被这些专家进行了评估和验证。我们评估逻辑交通控制是基于理论知识的。在这个过程中进行了两项活动，包括检查的要求和能力的问题，并在目标应用环境测试本体。由于逻辑交通控制已建成的基础上，如指定要求优化循环时间，逐步淘汰型，交通的移动和优化绿灯时间，每个阶段的序列中，第一项活动是最好的结果。逻辑交通控制满足所有的交通灯控制的需求，并能回答的能力问题。绩效评估机制，可以支持这种说法。在部分实验结果我们验证了这一过程。

第五篇：外文翻译

中原工学院毕业设计（论文）译文

超声测距系统设计

原文出处：传感器文摘 布拉福德：1993年第13页

摘要：超声测距系统技校在工业场车辆导航水声工程等领域都具有了广泛的应用价值，目前已应用于物理测量，机器人自动导航以及空气中与水下的目标探测、识别定位等场合，因此，深入研究超声的探测理论和方法具有重要的实践意义，为了进一步提高测量的精确度，满足工程人员对测量精度测距量程和测距仪使用的要求，本文研制了一套基于单片机的使拱式超声测距系统。关键词：超声波 测距仪 单片机

1、前言

随着科技的发展，人们生活水平的提高，城市发展建设加快，城市给排水系统也有较大发展，其状况不断改善，但是，由于历史原因合成时间性的许多不可预见因素，城市给排水系统，特别是排水系统往往落后于城市建设，因此，经常出现开挖已经建设好的建筑设施来改造排水系统的现象。城市污水给人们带来的困扰，因此箱的排污疏通对大城市给排水系统污水理，人们生活舒适显得非常重要。而设计研制箱涵排水疏通移动机器人的自动控制系统，保证机器人在箱涵中自由排污疏通，是箱涵排水系统疏通机器人的设计研制的核心部分，控制系统核心部分就是超声波测仪的研制。因此，设计好的超声波测距仪就显得非常重要了。

1.1课题背景

随着经济的发展与汽车科学技术的进步，公路交通呈现出行驶高速化、车流密集化和驾驶员非职业化的趋势。同时，随着汽车工业的飞速发展，汽车的产量和保有量都在急剧增加。但公路发展、交通管理却相对落后，导致了交通事故与日剧增，城市里尤其突出。智能交通系统ITS是目前世界上交通运输科学技术的前沿技术，它在充分发挥现有基础设施的潜力，提高运输效率，保障交通安全，缓解交通赌塞，改善城市环境等方面的卓越效能，已得到各国政府的广泛关注。中国政府也高度重视智能交通系统的研究开发与推广应用。汽车防撞系统作为ITS 发展的一个基础，它的成功与否对整个系统有着很大的作用。从传统上说，汽车的安全可以分为两个主要研究方向:一是主动式安全技术，即防止事故的发生，该种方式是目前汽车安全研究的最终目的;二是被动式安全技术，即事故发生后的乘员保护。目前汽车安全领域被动安全研究较多，主要从安全气囊、ABS(防抱死系统)和悬架等方面着手，以保证驾乘人员的安全。从经济性和安全性两方面来说，中原工学院毕业设计（论文）译文

这些被动安全措施是在事故发生时刻对车辆和人员进行保护，有很大的局限性，因而车辆的主动安全研究尤为重要，引出了本文研究的基于单片机的超声波测距系统。这个系统是一种可向司机预先发出视听语音信号的探测装置。它安装在汽车上，能探测企图接近车身的行人、车辆或周围障碍物;能向司机及乘员提前发出即将发生撞车危险的信号，促使司机采取应急措施来应付特殊险情，避免损失。

1.2 课题设计的意义

随着现代社会工业化程的发展，汽车这一交通工具正为越来越多的人所用，但是随之而来的问题也显而易见，那就是随着车辆的增多，交通事故的频繁发生，由此导致的人员伤亡和财产损失数目惊人。对于公路交通事故的分析表明，80%以上的车祸事由于驾驶员反应不及所引起的，超过65%的车辆相撞属于追尾相撞，其余则属于侧面相撞。奔驰汽车公司对各类交通事故的研究表明：若驾驶员能够提早1S 意识到有事故危险并采取相应的正确措施，则绝大多数的交通事故都可以避免。因此，大力研究开发如汽车防撞装置等主动式汽车辅助安全装置，减少驾驶员的负担和判断错误，对于提高交通安全将起到重要的作用。显然，此类产品的研究开发具有极大的实现意义和广阔的应用前景。

1.3超声波测距在汽车上应用的介绍

超声波倒车测距仪(俗称电子眼)是汽车倒车防撞安全辅助装置，能以声音或者更为直观的数字形式动态显示周围障碍物的情况。其较早的产品是用蜂鸣器报警，蜂鸣声越急，表示车辆离障碍物越近。后继的产品可以显示车后障碍物离车体的距离。其大多数产品探测范围在0.4～1.5m，有的产品能达到0.35～2.5m，并有距离显示、声响报警、区域警示和方位指示，有些产品还具备开机自检功能。目前市场上还出现了具有语音报警功能的产品。这些产品存在的主要问题是测量盲区大，报警滞后，未考虑汽车制动时的惯性因素，使驾驶者制动滞后，抗干扰能力不强，误报也较多。汽车防撞雷达之所以能实现防撞报警功能，主要有超声波这把无形尺子, 它测量最近障碍物的距离, 并告诉给车主。其实超声测距原理简单: 它发射超声波并接收反射回波, 通过单片机计数器获得两者时间差t, 利用公式S=Ct/2计算距离, 其中S为汽车与障碍物之间的距离, C为声波在介质中的传播速度。

本文介绍的超声测距系统共有2只超声波换能器(俗称探头),分别布置在汽车的后左、后右2个位置上。能检测前进和倒车方向障碍物距离, 通过后视镜内置的

中原工学院毕业设计（论文）译文

显示单元显示距离和方位, 发出一定的声响, 起到提示和警戒的作用。系统采用一片STC89C52单片机对两路超声波信号进行循环采集。超声波是指频率高于20HHZ的机械波。为了以超声波作为检测手段，必须产生超生波和接收超声波。完成这种功能的装置就是超声波传感器，习惯上称为超声波换能器或超声波探头。超声波传感器有发送器和接收器，但一个超声波传感器也可具有发送和接收声波的双重作用。超声波传感器是利用压电效应的原理将电能和超声波相互转化，即在发射超声波的时候，将电能转换，发射超声波；而在收到回波的时候，则将超声振动转换成电信号。超声波测距的原理一般采用渡越时间法。首先测出超声波从发射到遇到障碍物返回所经历的时间，再乘以超声波的速度就得到二倍的声源与障碍物之间的距离。测量距离的方法有很多种，短距离的可以用尺，远距离的有激光测距等，超声波测距适用于高精度的中长距离测量。因为超声波在标准空气中的传播速度为331.45米/秒，由单片机负责计时，单片机使用12.0M晶振，所以此系统的测量精度理论上可以达到毫米级。由于超声波指向性强，能量消耗缓慢，在介质中传播距离远，因而超声波可以用于距离的测量。利用超声波检测距离，设计比较方便，计算处理也较简单，并且在测量精度方面也能达到要求。超声波发生器可以分为两类：一类是用电气方式产生超声波，一类是用机械方式产生超声波。本设计属于近距离测量，可以采用常用的压电式超声波换能器来实现触发单元。

利用超声波测距的工作，就可以根据测量发射波与反射波之间的时间间隔，从而达到测量距离的作用。其主要有三种测距方法：

（1）相位检测法，相位检测法虽然精度高，但检测范围有限；

（2）声波幅值检测法，声波幅值检测法易受反射波的影响；

（3）渡越时间检测法，渡越时间检测法的工作方式简单，直观，在硬件控制和软件设计上都非常容易实现。其原理为：检测从发射传感器发射超声波，经气体介质传播到接收传感器的时间，这个时间就是渡越时间。本设计的超声波测距就是使用了渡越时间检测法。在移动车辆中应用的超声波传感器，是利用超声波在空气中的定向传播和固体反射特性（纵波），通过接收自身发射的超声波反射信号，根据超声波发出及回波接收的时间差和传播速度，计算传播距离，从而得到障碍物到车辆的距离。

中原工学院毕业设计（论文）译文 超声波测距原理

2.1 压电式超声波发生器原理

压电式超声波发生器实际上是利用压电晶体的谐振来工作的。超声波发生器内部结构，它有两个压电晶片和一个共振板。当它的两极外加脉冲信号，其频率等于压电晶片的固有振荡频率时，压电晶片将会发生共振，并带动共振板振动，便产生超声波。反之，如果两极板间未加电压，当共振板接收到超声波时，将压迫压电晶片做振动，将机械能转换为电信号，这是它就成为超声波接收器了。

测量脉冲到达时间的传统方法是以拥有固定参数的接收信号开端为基础的。这个信号恰恰选于噪音水平之上，然而脉冲到达时间被定义为脉冲信号刚好超过界限的第一时刻。一个物体的脉冲强度很大程度上取决于这个物体的自然属性尺寸还有它与传感器的距离。进一步说，从脉冲起始点到刚好超过界限之间的时间段随着脉冲的强度而改变。结果，一种错误便出现了——两个拥有不同强度的脉冲在不同时间超过界限却在同一时刻到达。强度较强的脉冲会比强度较弱的脉冲超过界限的时间早点，因此我们会认为强度较强的脉冲属于较近的物体。

2.2 超声波测距原理

超声波发射器向某一方向发射超声波，在发射时刻的同时开始计时，超声波在空气中传播，途中碰到障碍物就立即返回来，超声波接收器收到反射波就立即停止计时。超声波在空气中的传播速度为340m/s，根据计时器记录的时间t，就可以计算出发射点距离障碍物的距离(s)，即：s=340t/2

中原工学院毕业设计（论文）译文

3、超声波测距系统的电路设计

系统的特点是利用单片机控制超声波的发射和超声波自发射至接受往返时间的计时，单片机选用C51，经济易用，且片内有4K的ROM，便于编程。电路的原理如图1所示。

图1 电路原理图

中原工学院毕业设计（论文）译文

3.1 40kHz脉冲的产生与超声波发射

测距系统中的超声波传感器采用UCM40的压电陶瓷，它的工作电压是40kHz的脉冲信号，这由单片机执行下面的程序来产生。puzel：mov 14h，#12h

here： cp1.0；

nop；

nop；

nop；

djnz 14h，here；

Ret

前方测距电路的输出端接单片机P1.0端口，单片机执行上面的程序后，在P1.0端口输出一个40khz的脉冲信号，经过三极管T放大，驱动超声波发射头UCM40T，发出40khz的脉冲超声波，且持续发射200ms。右侧合作侧测距电路的输入端分别接P1.1和P1.2端口，工作原理和前方测距电路相同。

超声波发射持续200ms 输出40kHz方波

3.2 超声波的接收与处理

接收头采用与发射头配对的UCM40R，将超声波调制脉冲变为电压信号，经运算放大器ic1a和ic1b两级放大后加至IC2,。IC2是带有锁定环的音频译码集成块LM567，内部压控振荡器的中心频率f0=1/1.1R8C3，电容C4决定其带宽。调节R8在发射的载频上，则LM567输入信号大于25mv，输出端8脚由5由高电平跃变为低电平，作为中断请求信号，送至单片机处理。

前方测距电路的输出端接至单片机INT0端口，中断优先级最高，左、右测距电路的输出通过与门IC3A的输出接单片机的INT1端口，同时单片机P1.3和P1.4接到IC3A的输入端，中断源的识别由程序查询来处理，中断优先级为先右后左。部分源程序如下： receive1：push psw

push acc

clr ex1；关中断源1

jnb p1.1，right;P1.1引脚为0，转至右侧距电路中断服务程序

jnb p1.2,left;P1.2 引脚为0，转至左测距中断电路服务程序 returne：SETB EX1；

开外部中断1

pop acc

中原工学院毕业设计（论文）译文

pop psw

reti right：

...；

右测距电路中断服务程序入口

ajmp return

left：

...；

左测距电路中断服务程序入口

ajmp return

3.3 计算超声波传播时间

在启动发射电路的同时启动单片机内部的定时器T0，利用定时器的计数功能，记录超声波发射的时间和受到反射波的时间。当收到超声波反射波时，接受电路输出端产生一个负跳变，在INT0或INT1端产生一个中断请求信号，单片机响应外部中断请求，执行外部中断服务子程序，读取时间差，计算距离。其部分源程序如下：

RECEIVEO: PUSH PSW

PUSH ACC CLR EX0;

关外部中断0 读取时间值

MOV R7,TH0;MOV R6,TL0 CLR C MOV A,R6 SUBB A,#0BBH;MOV 31H,A;MOV A,R7 SUBB A,#3CH MOV 30H,A SETB EX0;POP ACC

POP PSW

RETI 对于一个平坦的目标，测量距离包括两个阶段：粗糙的测量和精细的测量。第一步：脉冲的传送产生一种简单的超声波

第二步：根据公式改变回波放大器的获得量直到回拨被检测到。第三步：检测两种回波的振幅与过零时间。

计算时间值 存储结果

开外部中断0

中原工学院毕业设计（论文）译文

第四步：设置回波放大器的所得规格输出，假定是3v。通过脉冲的周期设置下一个脉冲。根据第二部的数据设定时间窗。

第五步：发射两窜脉冲产生干扰波。测量过零时间与回波振幅。如果逆向发生在回波中，决定要不通过在低气压插入振幅。

第六步：通过公式计算距离y。

中原工学院毕业设计（论文）译文

4、超声波测距系统的软件设计

软件分为俩部分，主程序和中断服务程序。主程序完成初始化工作、各路超声波发射和接收顺序的控制。定时中断服务子程序完成三方向超声波的轮流发射，外部中断服务子程序主要完成时间值的读取、距离计算、结果的输出等工作。

中原工学院毕业设计（论文）译文

5、结论

对所要求测量范围30cm-200cm内的平面物体做了多次测量发现，其最大误差为1.5cm，且重复性好。可见基于单片机设计的超声波测距系统具有硬件结构简单、工作可靠、测量误差小等特点。因此，它不仅可用于移动机器人，还可以用在其他检测系统中。

思考：至于为什么不用接收管做放大电路，因为放大倍数搞不好，集成放大电路，还带自动电平增益控制，放大倍数为76db，中心频率是38k到40k，刚好是超声波传感器的谐振频率。

中原工学院毕业设计（论文）译文

参考文献

1.Fox，J.D.，Khuri-Yakub，B.T.and Kino，G.S.，“High Frequency Acoustic Wave Measurement in Air”，in Proceedings of IEEE 1983 Ultrasonic Symposium，October 31-2 November，1983，Atlanta，GA，pp.581-4.2.Martin Abreu，J.M.，Ceres,R.And Freire,T.,“Ultrasonic Ranging: Envelope Analysis Gives Improved Accuracy”,Sensor Review, Vol.12 No.1,1992,pp.17-21.3.Parrilla， M., Anaya,J.J and Fritsch C.,‖Digital Signal Processing Techniques for High Accuracy Ultrasonic Range Measurement:,IEEE Transactions: Instrumentation and Measurement.Vol.40 No.4, August 1991,pp.750-63.4.Canali, C., Cicco, G.D., Mortem, B., Prudenziati, M., and Taron, A., ―A Temperature Compensated Ultrasonic Sensor Operating in Air for Distance and Proxinmity Measurement‖, IEEE Trasaction on Industry Electronics, Vol, IE-29 No.4,1982, pp.336-41.5.Martin, J.M., Ceres, R., Calderon, L and Freire, T., ‖Ultrasonic Ranging Gets Themal Correction‖, Sensor Review, Vol, 9 No.3, 1989,pp.153-5.中原工学院毕业设计（论文）译文

Ultrasonic ranging system design Publication title: Sensor Review.Bradford:1993.Vol.13 ABSTRACT: Ultrasonic ranging technology has wide using worth in many field, such as the industrial locale, vehicle navigation and sonar engineering.Now it has been used in level measurement, self-guided autonomous vehicles, fieldwork robots automotive navigation, air and underwater target detection, identification ,location and so on.So there is an important practicing meaning to learn the ranging theory and ways deeply.To improve the precision of the ultrasonic ranging system in hand, satisfy the request of the engineering personal for the precision,the bound and the usage, a portable ultrasonic ranging system based on the single chip processor was developed.Keywords: Ultrasound r, Ranging System, Single Chip Processor

1.Introductive With the development of science and technology, the improvement of people’s standard of living, speeding up the development and construction of the city.Urban drainage system have greatly developed their situation is constantly improving.However, due to historical reasons many unpredictable factors in the synthesis of her time, the city drainage system.In particular drainage system often lags behind urban construction.Therefore, there are often good building excavation has been building facilities to upgrade the drainage system phenomenon.It brought to the city sewage, and it is clear to the city sewage and drainage culvert in the sewage treatment system.Confort is very important to people’s lives.Mobile robots designed to clear the drainage culvert and the automatic control system Free sewage culvert clear guarantee robot, the robot is designed to clear the culvert sewage to the core.Control System is the core component of the development of ultrasonic range finder.Therefore, it is very important to design a good ultrasonic range finder.1.1 subject background

With the development of economy and car scientific and technological progress, highway traffic presents driving fast pace, traffic dense is changed and the driver not professional trend.At the same time, along with the rapid development of auto industry, automobile yield and quantities are increased dramatically.But road development，中原工学院毕业设计（论文）译文

transportation management is relatively backward, leading to a large number of traffic accidents in some cities, especially prominent.Intelligent transportation system in the world, ITS transportation science and technology of advanced technology, ITS exerting existing infrastructure of potential, enhance the transport efficiency, safeguard traffic safety and ease traffic wager plug, improving urban environment aspects of outstanding performance, has received the governments of widespread concern.The Chinese government is also highly intelligent transportation system of the development and popularization applications.The automotive anti-collision system as ITS development of a base, ITS success to the whole system has a very significant role.Traditionally, auto safety said can be divided into two main research direction: first,it is active safety technology, including the prevention of accidents, the way is now automotive safety research ultimate purpose;second, it is passive safety technique, namely the occupant protection after the accident.Now automotive safety field passive safety more research, mainly from the airbag, ABS(antilock brakes)and suspension from the aspects such as to ensure safety of personnel rides.From the economic and safety two ways, these passive safety measures is the accident of vehicle and personnel moments protection, with great limitations, thus vehicle active safety research is particularly important, leads to a of this study is based on single chip ultrasonic ranging system.This system is a kind of can advance to the driver issued audio-visual speech signal detection devices.It is installed in cars that can detect trying to approach the body of a car pedestrians and vehicles or around obstacles, Can send to the driver and crew imminent danger ahead of the signal, prompting a crash drivers take emergency measures to cope with special danger, avoid the loss.1.2 question design significance

Along with the development of modern society industrialization process, car this traffic tools are used for more and more people, but any problem has obvious that along with the increase in vehicles, traffic accident, which led to the frequent occurrence of casualties and property losses number astonishing.For highway traffic accident analysis showed that more than 80% of the accident due to the driver reaction inferior things, caused more than 65% of vehicle collision, the rest belongs to tracing cauda collided belongs to the side collision.Mercedes-benz Automobile Company for all kinds of traffic accident research shows that: if the driver can early 1S are aware

中原工学院毕业设计（论文）译文

that a accident risk and take the appropriate corrective measures, the overwhelming majority of traffic accidents can be avoided.Therefore, vigorously research and development as the automotive anti-collision device etc active car auxiliary safe device, reduce the burden and misjudgments drivers to improve the traffic safety will play an important role.Obviously, this kind of product research and development has great realize meaning and broad application prospects.1.3 Ultrasonic ranging in automotive applications introduced

Ultrasonic back-draft rangefinder(known as electron optics)automotive anti-collision reversing device, can safe adjunct to sound or more intuitive digital form the dynamic display of around obstacles.Its earlier products is to use buzzer alarm, hum more anxious, and says vehicles from obstructions closer.Subsequent product can display the car from the body after the obstacles distance.Most of its products detection range in 0.4 ~ 1.5 m, some product can achieve 0.35 ~ 2.5 m, and have distance display, sound alarm, area-warning and azimuth instructions, some products also has the boot self-checking function.Still appeared on the market at present with voice alarm function of products.These products are the main problem is big, alarm measuring blind area lags behind, without considering the automobile braking inertial factors and make drivers brake lag, the anti-interference ability is not strong, misstatement or more.The automotive anti-collision radar is able to realize impact-proof alarm functions, basically have ultrasonic this intangible ruler, it recently obstacles distance measurement, and told to the owner.Actually ultrasonic range-finding principle simple: it emit ultrasonic echo, and receive reflected by microcontroller counter obtain both lag using formula S = t, Ct / 2 calculating distances, including S for cars and obstacles, C for the distance between the sound wave propagation in the medium speed.This paper introduces the ultrasonic ranging system only have 2 ultrasonic transducer(known as probe)respectively, decorate in cars left and right after after 2 position.Capable of detecting forward and reverse direction obstacle distance, the rearview mirror built-in display element display distance and direction, issued must be sound, plays the role of hints and alert.System USES a STC89C52 SCM two way ultrasonic signal cyclicly acquisition.Ultrasonic refers to the 20HHZ wave frequency is over.In order to use the ultrasonic detection means, must generate as ultrasonic wave and receiving damnation.Complete the functions of the device is called the

中原工学院毕业设计（论文）译文

ultrasonic sensor, habit, ultrasonic transducer or ultrasonic probe.Ultrasonic sensors have both transmitters and receivers, but a ultrasonic sensors can also has the sending and receiving the sound waves of the dual role.Ultrasonic sensors is using the principle of piezoelectric effect and ultrasonic energy conversion, be in namely emit ultrasonic, energy conversion, launch ultrasonic, And in the stockades, received echo ultrasonic vibration into electrical signal.Ultrasonic ranging principle generally USES the time method for the crossing.First measured ultrasonic from the launch to meet obstacles returns experience of time, again multiply ultrasonic speed of get twice the distance between the sound source and obstacles.Measuring distance a variety of ways, short can use ruler, long-range laser displacement etc, are suitable for high accuracy of ultrasonic ranging in long distance measurement.Because of ultrasound in standard air of propagation speed 331.45 meters per second, by single-chip microcomputer is responsible for timing, SCM use 12.0 M crystals, so the system of measurement precision theory can achieve mm level.Because of ultrasonic directivity strong, energy consumption is slow, in a medium transmission distance, thus ultrasonic can be used for distance measurement.Using ultrasonic detection distance, the design is more convenient, computing procese also relatively simple, and the measurement precision can also meet the requirements.Ultrasonic generator can be divided into two kinds: one kind is to use electrical means producing ultrasonic, one kind is with mechanical approach to producing ultrasonic.This design belongs to nearly distance measurement, can use commonly used the piezoelectric ultrasonic transducer to achieve trigger unit.Using ultrasonic ranging work, can according to measuring launch reflection wave wave and the time interval between the measured distance, so as to achieve the effect.It mainly have three ranging methods:

(1)phase assay, phase assays high precision, but detection though limited range，(2)sound amplitude assay, acoustic amplitude assay vulnerable reflection wave influence;

(3)ferrying more time assay, crossing the time assay way of working is simple, intuitive, in hardware control and software design are very easy to implement.Its principle is: from the launch emit ultrasonic detection sensor, the gas medium spread to receive sensor of time, this time is crossing the more time.This design is the use of ultrasonic ranging the crossing the time assay.In the mobile vehicles of the application 15

中原工学院毕业设计（论文）译文

of ultrasonic sensor is the use of ultrasound in air of directional spread and solid reflective characteristics(p-wave)and by receiving their launch ultrasonic reflecting signal, according to the ultrasonic issued and echo receiving the Windows and propagation speed, calculate transmission distance, thus obtains the obstacles to vehicle distance.中原工学院毕业设计（论文）译文

2.A principle of ultrasonic distance measurement

2.1 the principle of piezoelectric ultrasonic generator

Piezoelectric ultrasonic generator is the use of piezoelectric crystal resonators to work.Ultrasonic generator, the internal structure as shown, it has two piezoelectric chip and a resonance plate.When it’s two plus pulse signal, the frequency equal to the intrinsic piezoelectric oscillation frequency chip, the chip will happen piezoelectric resonance, and promote the development of plate vibration resonance, ultrasound is generated.Conversely, if the two are not inter-electrode voltage, when the board received ultrasonic resonance, it will be for vibration suppression, then it becomes the ultrasonic receiver.The traditional way to determine the moment of the echo’s arrival is based on thresholding the received signal with a fixed reference.The threshold is chosen well above the noise level, whereas the moment of arrival of an echo is defined as the first moment the echo signal surpasses that threshold.The intensity of an echo reflecting from an object strongly depends on the object’s nature, size and distance from the sensor.Further, the time interval from the echo’s starting point to the moment when it surpasses the threshold changes with the different intensities arriving exactly at the same tome will surpass the threshold at different moments.The stronger one will surpass the threshold earlier than the weaker, so it will be considered as belonging to a nearer object.2.2 The principle of ultrasonic distance measurement Ultrasonic transmitter in a direction to launch ultrasound, in the moment to launch the beginning of time at the same time, the spread of ultrasound in the air, obstracles on his way to return immediately, the ultrasonic reflected wave wave received by the reveiver immediately stop the clock.Ultrasonic in the air as the propagation velocity of 340m/s, according to the timer records the time t, we can calculate the distance between the launch distance barrier(s), that is:s=340t/2

中原工学院毕业设计（论文）译文

3.Ultrasonic Ranging System for the Second Circuit Design

System is characterized by single-chip microcomputer to control the use of ultrasonic transmitter and ultrasonic receiver since the launch from time to time, single-chip selection of 8751,economic-to –use, and the chip has 4K of ROM, to facilitate programming.Circuit schematic diagram shown in Figure 1.Figure 1 circuit principle diagram

中原工学院毕业设计（论文）译文

3.1 40 kHz ultrasonic pulse generated with the launch

Ranging system using the ultrasonic sensor of piezoelectric sensors UCM40, its operating voltage of the pulse signal is 40kHz, which by the single-chip implementation of the following procedures to generate.Puzel:mov 14h,# 12h;ultrasonic firing continued 200ms here:cpl pl.0;output 40 kHz square wave

nop;

nop;nop;djnz 14h, here;ret Ranging in front of single-chip termination circuit P1.0 input port, single chip implementation of the above procedure, the P1.0 port in a 40kHz pulze output signal, after amplification transistor T, the drive to launch the first ultrasonic UCM40T, issued 40kHz ultrasonic pulse, and the continued launch of 200ms.Ranging the right and the left side of the circuit, respectively, then input port P1.1 and P1.2, the working principle and circuit in front of the same location.3.2 Reception and processing of ultrasonic

Used to receive the first launch of the first pair UCM40R, the ultrasonic pulse modulation signal into an alternating voltage, the op-amp amplification IC1A and after polarization IC1B to IC2.IC2 is locked loop with audio decoder chip LM567, internal voltage-controlled oscillator center frequency of f0=1/1.1R8C3, capacitor C4 determine their target bandwidth.R8-conditioning in the launch of the carrier frequency on the LM567 input signal is greater than 25Mv, the output from the high jump 8 feet into a low-level, as interrupt request signals to the single-chip processing.Ranging in front of single-chip termination circuit port INT0 interrupt the highest priority, right or left location of the output circuit with output gete IC3A access INT1 port single-chip, while single-chip P1.3 and P1.4 received input IC3A, interrupted by the process to identify the source code is as follows: receivel:

push psw

push ace

中原工学院毕业设计（论文）译文

cir ex1: related external interrupt 1

jnb p1.1, right;P1.1 pin to 0, ranging from right to interrupt service rountine circuit

jnb p1.2, left;P1.2 pin to 0, to the left ranging circuit

interrupt service routine return:SETB EX1;open external interrupt 1

pop

acc pop

psw reti right:…;right location entrance circuit interrupt service rountine

Ajmp Return left:…;left Ranging entrance circuit interrupt service rountine

Ajmp Return

3.3 The calculation of ultrasonic propagation time

When you start firing at the same time start the single-chip circuitry within the timer T0, the use of timer counting function records the time and the launch of ultrasonic reflected wave received time when you receive the ultrasonic reflected wave, the receiver circuit outputs a negative jump in the end of INT0 or INT1 interrupt request generates a signal, single-chip microcomputer in response to external interrupt request, the implementation of the external interrupt service subroutine, read the time difference, calculating the distance.Some of its source is as follows: RECEIVE0: PUSH PSW PUSH ACC CLR EX0;related external interrupt 0 MOV R7, TH0;read the time value MOV R6, TL0 CLR C MOV A, R6 SUBB A,#0BBH;calculate the tome difference MOV 31H, A;storage results MOV A, R7 SUBB A,#3CH

中原工学院毕业设计（论文）译文

MOV 30H,A SETB EX0;open external interrupt 0 POP ACC POP PAW RETI For a flat target, a distance measurement consists of two phases: a coarse measurement and, a fine measurement: Step 1: Transmission of one pulse train to produce a simple ultrasonic

Wave.Step 2: Changing the gain of both echo amplifiers according to equation，until the echo is detected.Step 3:detection of te amplitudes anf zero-crossing times of both echoes.Step 4:setting the gains of both echo amplifiers to normalize the output at, say 3 volts.Setting the period of the next pulses according to the: period of echoes.Setting the time window according to the data of step 2.Step 5:sending two pulse trains to produce an interfered wave.Testing the zero-crossing in the echo,detemine to otherwise calculate to by interpolation using the amplitudes near the trough.Derive t sub ml and t sub m2.Step6: Calculation of the distance y using equation.中原工学院毕业设计（论文）译文

4.The ultrasonic ranging system software design

Software is divided into two parts, the main program and interrupt service routine.Completion of the work of the main program is initialized, each sequence of ultrasonic transmitting and receiving control.Tnterrupt service routines from time to complete three of the rotation direction of ultrasonic launch, the main external interrupt service subroutine to resd the value of completion time, distance calculation, the results of the output and so on.中原工学院毕业设计（论文）译文

5.Conclusions

Required measuring range of 30cm~200cm objects inside the plane to do a number of measurements found that the maximum error is 0.5cm, and good reproducibility.Single-chip design can be seen on the ultrasonic ranging system has a hardware structure is simple, reliable, small features such as measurement error.Therefore, it can be used not only for mobile robot can be used in other detection systems.Thoughts: As for why the receiver do not have the transistor amplifier circuit, because the magnification well, integrated amplifier, but also with automatic gain control level, magnification to 76dB, the center frequency is 38k to 40k, is exactly resonant ultrasonic sensors frequency.中原工学院毕业设计（论文）译文

REFERENCES 1.Fox,J.D.,Khuri-Yakub, B.T.and Kino, G.S., ‖High Frequency Acoustic Wave Measurement in Air‖, in Proceedings of IEEE 1983 Ultrasonic Symposium, October 31-2 November, 1983, Atlanta, GA, pp.581-4.2.Martin Abreu,J.M.,Ceres,R.and Freire, T.,‖Ultrasonic Ranging: Envelope Analysis Gives Improved Accuracy‖, Sensor Review, Vol.12No.1,1992, pp.17-21.3.Parrilla， M., Anaya,J.J and Fritsch C.,‖Digital Signal Processing Techniques for High Accuracy Ultrasonic Range Measurement:,IEEE Transactions: Instrumentation and Measurement.Vol.40 No.4, August 1991,pp.750-63.4.Canali, C., Cicco, G.D., Mortem, B., Prudenziati, M., and Taron, A., ―A Temperature Compensated Ultrasonic Sensor Operating in Air for Distance and Proxinmity Measurement‖, IEEE Trasaction on Industry Electronics, Vol, IE-29 No.4,1982, pp.336-41.5.Martin, J.M., Ceres, R., Calderon, L and Freire, T., ‖Ultrasonic Ranging Gets Themal Correction‖, Sensor Review, Vol, 9 No.3, 1989,pp.153-5.24