毕业论文中英语短片（大全）

第一篇：毕业论文中英语短片（大全）

主题： 翻译

1、MAN MARINE DIESEL ENGINE MAN

The latest large bore two storke MAN, engine is the KSZ 90/163B series in cylinder number from 6 to 12 and developing2,700kW(3,672HP)/cyl.The engine operates at 122r/min, with an M.E.P of 13bar and a mean piston speed of 6.5m/s.The bedplate is of fabricated design and consists of weo I-shaped longitudinal girders with transverse menbers into which the cast steel bearing housings are welded.The thrust bearing casting is incorporated into the bedplate.Columns have been replaced by frames constructed of box shaped longitudinal girders.Thew fabricated top and bottom sections run the full length of the engine and are mounted on the bedplate.Such an engine frame helps to stiffen the engine and so protect the bearings from the deformation forces transmitted via the ship's double bottom.The cast iron guideways for the crosshead are attached to the top section and seal off the crankcase.The cylinder jackets are individual castings bolted together to form one

continuous member.The one piece cylinder liners are fitted into the jackets from the top and a cast steel strong back is fitted in way of the combustion space to help absorb gas forces.The scavenge process is the MAN loop system and the scavenge and wxhaust ports are arranged in two tiers and are carried far around the liner.The vertical lands between the ports are cooled by water passing hrough cast in tubes and hence to passages arranged around the liner above the exhaust ports.Each cylinder cover is in two parts, the lower section is of special thin walled forged steel permitting the area in way of the combustion gases to be intensively cooled whilst absorbing thermal stresses and this is held in position by an upper supporting unit of cast iron, which transmits the gas forces to the cylinder jackets via long studs.The joint face between the cylinder cover and the liner is arranged as far from the combustion process as possible.The gas loads on the engine structure are constrained by means of hydraulic preloaded tie rods which connect the bedplate, frame sections and cylinder jackets into a single unit.The crankshaft is of the semi-built tybe, with the journal being shrunk into the forged or cast steel crank throws.With the exception of the six-cylinder engine, it is in two arts joined by fitted bolts.The coupling flange for attachment to the propeller shaft also accommodates the turning gear and is integrally forged with the crankshaft.The aft end section also incorporates a thrust collar.The drive for the camshaft gear train is taken from a spur gear which for a six cylinder engine is the couping end and for 7 to 12 sylinder engines the drive is located in the middle

of the engine.The piston crown is of forged steel and is designed for intensive cooling;the central supporting body is of cast steel and is mainly suvjected to compressive stress.The two components are bolted together and connected to the piston rod.A single piece piston skirt fitted with bronze rings guides the piston in the cylinder liner.The piston ring grooves for a standard engine are flame hardened against wear.The crosshead pin bearings are whte metal lined shells lubricated by means of highpressure pumps.The piston forces are transmitted over the entire length of the crosshead pin then to the connecting rod via the lower half single bearing shell.The principle of hydrostatic lubrication has been applied to the crosshead using high-pressure lubricators.This is achieved by means of high pressure rod,high pressure oil is delivered to the ower part of the crosshead bearing, the pumps press oil film is maintained at all times and on all loads between the journal and the shell.Scavenging of the cylinder liner is on the loop scavenge system and constant pressure of the exhaust gas is used to drive the turbochargers.During running up and in the lower partial load range the turbochargers are assisted by electrically driven auxiliary blowers connected before the compressors of the main blowers.In the upper power range the auxiliary blowers are disconnected.Diffusers are fitted in the exhaust system and facilitate charge removal and scavenging in each cylinder.The diffuser also prevents pressure pulses from one cylinder interfering with another during operation.2、MAN-B&W MC ENGINE MAN-B&W MC

MAN-B&W K90 MC-C engine is a large crosshead tybe two-stroke engine with a broe of 900mm, a 2,300mm stroke and an operating speed of 104r/min.It is constructed with between six and twelve cylinders.Developed as one of the extensive range of the manufacturer's MC engines, it is of the power and speed best suited to large, fast container ships.The increase in running speed is obtained by a slight decrease in engine stroke.High thermal efficiency is maintained by an increase in mean effective pressure(M.E.P.).Construction can be considered generally as typical for the whole range.The engine bedplate is of rigid box form, fabricated from steel plates with main bearing supports of cast steel.Welded 'A' frames are assembled into a frame box which contains the crankcase, the crosshead guides and also supports the wheels for the chain drive of the camshaft.A cast iron cylinder frame accommodates the scavenge space between the cylinder jacket and the diaphragm, both of which are water-cooled.Long pre-stressed tie bolts are fitted between the top of the frame and the underside of the bedplate girders.The cylinder liner is of alloy cast iron, its upper flange lands on top of the frame and has bore cooling.It is secured by a forged steel cylinder cover which is also bore cooled and is shaped internally to accommodate most of the combustion space.Cylinder luvricating oil is injected at one level in the liner.Pistons have a chrome-molybdenum alloy steel crown with hard chrome-surfaced ring grooves in which four compression rings are fitted.In this particular model a protective layer of Inconel is welded to part of the crown surface to prevent high temperature corrosion.The piston is oil cooled, oil being supplied by a telescopic gland to the crosshead and then through the piston rod.It is returned from the crosshead to a slotted pipe in the crankcase.A short cast iron skirt is added.The crown is bolted to the piston rod at an inner support ring.Surface hardening reduces wear on the piston rod at the diaphragm gland.The rod is bolted ata the top of a cylindrical crosshead which is of large diameter and incorporates a full-length bottom half-bearing shell.Floating guide shoes are attached at each end.The crankshaft may be either semi-built up or of welded construcion, with large journals and pins.All crankcase hearings are of white metal.Main bearings have thick shells, crankpin(bottom end)and crosshead(top end)bearing have thin-wall shells.White metal is used for the guide surfaces.The exhaust valves are operated hydraulically under oil pressure from cam-timed actuated pistons.They have air compressed springs which allows them to be rotated by vanes.The valve spindles are usually manufactured by the hot isostatic pressure(HIP)method, a compound Nimonic and austenitic steel part construction.Valve housing is cooling at its seat and spindle guide bush but its upper duct is uncooled to avoid low temperature corrosion.Fuel pumps are cam driven and timed by the plunger helix.An adjustable barrel allows variable ignition timing to maintain combustion efficiency at low speed and can be adjusted to match the ignition quality of fuels.Pump timing is changed for astern operation by a link connected at the cam roller guide which is activated by compressed air.Each pump supplies three identical fuel injectors for the

corresponding unit.Injectors are uncooled but they circulate hot fuel oil directly white their needle valves are in the closed position.The engine operates with a constant pressure system, with uncooled turbochargers.Two auxiliary blowers are fitted to operate at low charge air pressure or at low

engine revolutions.A number of waste heat recovery and power take-off systems can be operated under running conditions.

第二篇：英语电影配音短片制作方法

英语电影配音短片制作方法

1.准备工作：

（一）下载所需软件。可从官方网站下载也可从百度搜索。软件一：mediacoder 官方网站下载：http://www.xiexiebang.com 下载电影所需的英文字幕。

小贴士：将下载下来的字幕文件名改为和对应的视频文件同名，并和视频文件放在一个文件夹里，这样用暴风影音播放的时候就能自动加载英文字幕啦！

2.配音短片剪辑制作流程

（一）使用mediacoder截取配音所需的电影片段并配上英文字幕。

从菜单选择：文件→ 添加文件



修改视频格式：点击视频，修改格式为XviD,容器为AVI；如图１ 

时间起始与终止值设定：观察所选配音片段在整部影片中的时间起始与终止的值。点击时间按纽，并设置。



添加字幕：设置语言，添加字幕文件。（请注意：请最好使用.srt格式的字幕文件，否则有可能转换出来的视频显示不出字幕。）如图２



设置输出路径：点击窗口上方的“...”按钮，选择配音片段的输出路径。



点击start ,等待转换编码任务。完成后界面如图示３。

图１

?/P>

图２

?/P>

图３

（二）使用cooledit pro 2.1 进行音频处理，将影片中的人声消去，制作消人声音频文件



打开软件，默认视图为多音轨视图。

点击右键插入视频文件。如图４



选择左上方“音频为”如图示，按鼠标左键拖动复制到音轨３，按住鼠标右键拖动音轨３至左对齐。如图５ 

点击音轨2左侧的M按钮使其静音。



双击音轨3的波形图，或者选中音轨3，按F12 可以切换为单轨视图，然后选择“效果”→波形／振幅→声道重混缩。如图６ 

然后在预置列表中选择vocalcut。确定即可。



再次按F12切换到多轨界面。选择 “文件→混缩另存为”，保存格式选择.wav音频文件格式。如图７ ?/P> ?/P>

图４

?/P>

图５

?/P>

（三）使用virtual Dub软件，将消人声音频与原视频重新合成无人声有字幕的视频文件。



打开 文件→视频文件



音频→ＷＡＶ音频→找到消除了人声的文件。如图8 

视频→压缩→在压缩列表中选择一个编码器，推荐XviD MPEG-4 Codec。如图9，图10 

文件→另存为。等待转换完成即可。

图8

图9

图10

第三篇：英语毕业论文

中国式英语初探

中国英语初探

［摘 要］ 随着中国政治经济的发展，中国英语也日益形成。本文阐述了中国英语与中国式英语的区别，对中国英语产生的原因及特点进行了分析。

［关键词］ 中国英语 中国式英语 本土化

1、英语的使用现状

众所周知,英语是当今世界上主要的国际通用语言之一。对于许多国家而言，英语是她们的国语，是大多数人的生活语言、官方语言或政府工作语言,是国民交流、社会生活的重要途径和工具。随着经济全球化和贸易一体化的到来, 英语在世界其他非英语国家都作为外语在学习。

2、英语的区域性变体及其成因

橘子生在淮南和淮北会产生味道的不同，英语的迅速国际化必然会引起英语一定程度上的本土化。英语本土化主要体现在英语在世界范围内具有代表性的变体, 这些英语变体既保持了标准英语的特点,又增添了有别于标准英语的某些特征。如英国英语、美国英语、印度英语、新西兰英语、澳大利亚英语、马耳他英语等。但这些英语变体都有其共同的或独特的历史原因。从17世纪末起,英国就开始其海外扩张政策,随着对海外殖民地的统治与掠夺,英语逐渐发展为一种国际语言。但语言所反映的现实生活,由于受到不同国家和地区独特的本土文化、发音习惯和思维模式,从而出现了一些有别于标准英语的区域性变体。这些区域性变体英语在长期的发展过程中, 既保留了标准英语的基本框架,还吸收了其他殖民者如法国人、德国人、西班牙人和荷兰人等所使用的语言,并结合了大量的印第安人的本土语言，逐渐形成了如今各种英语的基本词汇。在中国,英语作为国际语言，虽然还没有完全走进百姓生活,但英语早已经作为各级各类学校的知识课与技能课在传授。

因此，英语的中国化正在日益形成。

3、中国英语产生的原因

大多数学者认为：中国英语是以规范英语为基础，用来表达中国特有的事物与现象的一种英语变体。它是中国文化与英语语言相结合的产物，是国际使用型的英语中国本土化的体现。它是有别于中式英语（Chinglish）的一种规范英语。

从前看到有人在信中写到 “Long time no see” 的时候，还会感慨，真是典型的中式英语。但如今这句 “好久不见” 也被收在新编实用英语综合教程1（2002年版）中（Unit 1）,作为标准中国英语来使用。“no moneyno talk”(没钱就没商量)以及毛主席的题词 “好好学习，天天向上” 也被直译成 “Good good Study, Day day up”。首先，由于英汉两种文化上存在着许多的差异，汉语文化中的一些特有的事物与现象往往在英语中无法找到相对应的表达。这时人们常通过音译、借译、语义再生等手段，使汉语词汇进入英语交际。因此，大量的中国英语词汇中便体现出中国英语的本土化特色。中国英语在表达中国特有事物或现象方面有着独特的作用。全球语言监督会的主席帕亚克曾经对媒体表示,“由于中国经济增长的影响,它现在对国际英语的冲击比英语国家还大”。不断地创造新词汇，使英语成为世界混合语。自1994年以来加入国际英语行列的词汇中, 中国式英语贡献了5%-20%,超过任何其他来源。例如：福娃（fuwa）、台风（typhoon）、功夫（kongfu）、太极（taiji）、武术（wushu）、儒家思想（Confucianism）、四书（FourBooks），五经（Five Classics）、家庭联产承包责任制（family contract re-sponsibility system）、知识经济（knowledge economy）、和平崛起（peacefulrising）等。这些中国式英语词汇都折射出了中国不同时期的时代特征。其次，汉语文化也在物质文化和精神文化上同时影响着英语：包括生产生活方式、自然地理环境、政治文化制度、风土人情习惯、伦理道德观念、宗教、科学、艺术等方面。英语国家的英语不能完全照搬照抄于中国国情的现状使得汉语在英语中的渗透变得尤为必要。例如，中国特有的传统节日诸如端午节、中秋节分别别翻译成 Dragon-boat Festival、Mid-autumn Day,把传统中国节日中的赛龙舟的习俗译于其中。此外，传统中医的许多专有名词在英语中并没有现成的对应词汇,若忽略中西方文化上的差异而强行直译，是会引起天大误解的。

例如把中医的 “生气”（生命力）译为 “发怒” ；把 “带下医”（妇科医生）翻译为 “躲在裙带下的医生”;“公孙” 是人体的一个穴位名称，国内一些专家就曾将其译为 “爷爷和孙子”。更有笑话说，有些菜馆为了与国际接轨，所有的菜谱统一配置了英文名，把 “童子鸡” 翻译成了 “chicken without sexual life”，“四喜丸子”

成了 “Four glad meatballs”。

再次，建国后，尤其是改革开放以来，中国在政治、经济、军事、文化、科学技术和国际地位等方面都发生了重大的变化，国际影响力日趋增强，中国文明的力量和威望使中国文化在英语中有了大规模地影响和渗入，越来越多的外国人想更多地了解中国传统文化。面对这些情况，人们通常通过音译、借译等手段，使中文词汇进入英语便成为了必然。因此，使用中国英语，更忠实地反映中国古、现代名著更有利于东西方文化交流。以美国著名华裔女作家汤亭亭为例，她把花木兰的故事传遍了英语世界，她经常强调她的第一语言是汉语。在她的英文小说里，她总是实验性地加入汉语，使她的英语更加完美。

4、中国英语的特点

不同国家和地域都因历史、地理及风土人情的不同使英语在本国使用中具备了自己的本土化特色。以印度英语为例。印度人英语口音重、语速快，说起话来满嘴里跑舌头，辅音r发颤音。印度式英语把标准英语中本应该咬舌送气的音 th 简化为 t。而且印度人发的t的音，又接近d的音。此外，受15世纪进入印度的英国商人影响，印度英语中仍然保留了一些现代英语中很少使用的词汇及用法。尽管中国英

语是以规范英语为核心的，然而，作为“世界英语”(World

Englishes)的一个组成部分的中国英语，在汉语中国文化与英语的漫长接触中，也与 “美国英语”、“印度英语”、“巴基斯坦英语”、“澳大利亚英语” 的发展一样，具备了自己的中国特色。在语音、词汇、语法、语篇等各个语言层面产生了具有中国特色的变异分化。首先，在语音方面主要体现在来自不同省、市、自治区的中国人说出的英语南腔北调，有的不会发th，有的分不清r和l、n和l。例如,很多人分不清楚read和lead、think和sink，three和free，night和light等。其次，在词汇方面具体表现为数量大、淘汰率低、翻译方式灵活多样、表意准确，许多汉语介词常见诸英美报刊，许多汉语固有的词汇大量的丰富了英语词库。例如：希望工程 Hope Project，拜年 pay New Yearcall, “豆腐渣” 工程

jerry-built project，三好学生three-good student等。再次，在语法方面，由于受到汉语思维与汉语句法的影响，中国英语倾向于修饰成分前置，致使中国英语在语篇内句子简短、单句偏多。例如：钱钟书先生所说的 “get the meaning,forget the words”（得意忘言）。最后，就篇章和文体而言，汉语的陈述和描写跟英语相比更加崇尚华丽，而英语写作崇尚平实；英语论说文喜欢用委婉含蓄的句式陈述观点，而汉语则喜欢直截了当。但中国英语应用得当，它能更忠实地反映原文；尤其在表达中国特有事物或现象方面，它有独特的作用。例如：《西游记》

就常被直接译为Pilgrimage to the West，Pilgrimage一词既有 “朝

圣、朝觐” 的意义，又包含了 “旅行、漫游” 的意思，忠实地译出了 《西游记》 的题目中的含义，又涵指了内容中师徒几人赴西天取经的征途。

5、总结 中国英语在跨文化交际中有着极其重要的作用，作为英语跟中国文化接轨的载体，它承载了中国文化的丰富内涵。在跨文化交际中，采取 “求同存异” 的原则，既要求充分尊重英语的语用原则和民族文化习俗，也应该理解和容忍中国英语中的异国特色。因此，在使用中国英语时，应注意以英美人的思维方式与中国文化相结合，避免把中国英语与中式英语相混淆，使中国英语的使用更能适应动态的，不可预知的情况，发挥其应有的作用。

参考文献 ［1］李文中.中国英语与中国式英语［J］.外语教学与研究，1993,(4)

［2］桂灿昆.美国英语应用语音学［M］.上海:上海外语教育出版社，1999

［3］杜瑞清，姜亚军.近二十年 “中国英语” 研究述评［J］.北京：外语教学与研究,2001,(1)

［4］邱立中.“中国英语” 质疑［J］.外语教学，2002,(6)

［5］刘祥清，晏小花.“中国英语” 研究与英语写作［J］.衡阳:南华大学学报，2004,(4)

［6］潘章仙.中国英语变体中的语言和文化认同 / 语言学论丛［M］.北京：北京大学出版社，2005，12

第四篇：英语毕业论文

英汉翻译与评论：Attitude Is Everything Original：

Jerry was the kind of guy you love to hate.He was always in a good mood and always had something positive to say.When someone would ask how he was doing, he would reply, “If I were any better, I would be twins!”

He was a unique manager because he had several waiters who had followed him around from restraint to restraint.The reason the waiters followed Jerry was because of his attitude.He was a natural motivator.If an employee was having a bad day, Jerry was there telling the employee how to look on the positive side of the situation

.Seeing this style really made me curious, so one day I went up to jerry and asked him, “I don't get it！You can’t be a positive person all of the time.How do you do it?”

Jerry replied,“ Each morning I wake up and say to myself ,jerry ,you have two choices today.You can choose to be in a good mood or you can choose to be in a bad mood.I choose to be in a good.Each time something bad happens, I can choose to be a victim or I can choose to learn from it.I choose to learn from it.Every time someone comes to me complaining, I can choose to accept their complaining or I can point out the positive side of the life.I choose the positive side of life.” “Yeah, right, it's not that easy,” I protested.“Yes, it is,” Jerry said.“Life is all about choices.When you cut away all the junk, every situation is a choice.You choose how to react to situations.You choose how people will affect your mood.You choose to be in a good or a bad mood.The bottom line: it's your choice how you live you life.”

I reflected on what jerry said.Soon thereafter, I left the restraint industry to start my own business.We lost touch, but I often thought about him when I made a choice about life instead of reacting to it.Several years later, I heard that Jerry did something you are never supposed to do in a restaurant business: He left the back door open one morning and was held up at gunpoint by three armed robbers.While trying to open the safe, his hand, shaking from nervousness, slipped off the combination.The robbers panicked and shot him.Luckily, Jerry was found relatively and rushed to the hospital.After 18 hours of surgery and weeks of intensive care, Jerry was released from the hospital with fragments of the bullets still in his body.I saw Jerry about six months after the accident.When I asked him about how he was, he replied,“ If I were any better, I'd be twins.Want to see my scars?” I declined to see his wounds, but did ask him what had gone through his mind as the robbery took place.“The first thing that went through my mind was that I should have locked the back door,” Jerry replied.“ then, as I lay on the floor, I remembered that I had two choices：I could choose to live or I could choose to die.I choose to live.”

“Weren’t you scared? Did you lose consciousness?’’ I asked.Jerry continued,” The paramedics were great.They kept telling me I was going to be fine.But when they wheeled me to the emergency room and I saw expressions on the faces of the doctors and nurses, I got really scared.In their eyes I read, he’s a dead man.I knew I needed to take action.”

“ What did you do？” I asked.“Well, there was a big nurse shouting questions at me,” Jerry.“She asked if I was allergic to anything.Yes, I replied.The doctors and nurses stopped working as they waited for my reply.I took a deep breath and yelled, bullets！Over their laughter, I told them, I am choosing to live.Operate me as if I am alive, not dead.”

Jerry lived thanks to the skill of his doctors, but also because of his amazing attitude.I learned from him that every day we have the choice to live fully.Attitude, after all, is everything.（选自高等教育出版社 综合课程1 Unit 3）

译文：

态度决定一切

杰瑞是那种让你又爱又恨的人。他总是乐呵呵的，总有许多鼓励的话要说。当有人问他他是怎么做到这一切是，他总是回答:“如果我可以变得更好，我就成为双胞胎了。”

他是一个独一无二的经理，因为他有一批忠心的跟随他的服务员，跟随他从一家酒店转到另一家酒店工作。这些员工跟随杰瑞是因为他的态度。他是一个天生的励志家。如果有员工遇到不幸，杰瑞总会告诉员工怎么去看到事务的积极面。

我非常好奇看到这样的人，所以有一天我去找杰瑞，问: “我不明白。你不可能永远乐观，你是怎么办到的？”

杰瑞回答说：“每天早上我起床是总会对自己说，‘杰瑞你今天有两种选择。你可以选择坏心情也可以选择好心情。’我选择好心情。每一次不幸发生时，我可以选择成为一个受害者或从中吸收教育。我选择吸取教训。每当人们开始抱怨，我可以选择接受他们的抱怨或指出人生的积极面时，我选择指出人生的积极面。”

“嗯，对，可那并不容易。”我提出异议。

“是的，的确，”杰瑞说，“人生就是选择。当你铲除所以障碍时，任何情况下都是一次选择。你选择如何应对情况。你选择人们任何影响你的情绪。你选择好心情或坏心情。但根本点是:你选择如何过你的生活！”

我很认真的思考杰瑞的话，但是没过多久，我就离开酒店去发展我自己的事业。我们失去了联系，但是每当我面临生活做出选择时，我会时常想起他。

几年以后，我听说杰瑞经历了一些你在酒店绝不会经历的事：一天早晨，他打开后门时，被三个武装劫匪用枪指住打劫。

在他试图打开保险柜时，他的手因为紧张而颤抖的拨弄密码键，却被受到惊吓的劫匪开枪射中了。幸运的是，杰瑞在比较快的时间被发现并送往当地的医院。

在18个小时的外壳手术和几周的强化护理后，杰瑞出院了。但他的身体里仍然留有子弹的碎片。

在那次意外的六个月后我遇到了杰瑞。当我问他感觉怎样时，他回答：“如果我可以变得更好，我就成为双胞胎了。想看看我的伤疤吗？”

我回绝了看他的伤疤，当你却问他当抢劫发生时他的脑中在想什么。

“我想到的第一件事就是我本应该锁上门。’’杰瑞说，“然后，当我躺在地板上时，我记得我有两种选择：我可以选择活下去，或者死亡。我选择活下去。”

“你难道不怕吗？你有没有失去意识？”我问。

杰瑞继续说：“护工们非常了不起。他们一直告诉我，我会好起来。但他们把我推进急救室时，我看见医生和护士脸上写满了忧虑，我真的很害怕。在他们眼里，我看到，‘他就快死了。’我明白自己必须采取行动。”

“那你做了什么呢？’’我问。

“嗯，有一个护士大声问我问题，”杰瑞说，“她问我是不是对什么过敏。‘有’，我说。医生和护士就放下手中的活等我回答。我深呼一口气，大叫，‘子弹！’透过他们的笑声，我告诉他们，‘我要活下去。我要像活人那样接受手术，而不是死人。’’’

杰瑞将他的活下来的奇迹归功与他的医生的精湛的技术，但也因为他那不可思议的态度。我从他身上了解到：每一天我们的生活中都充满选择。

总而言之，态度决定一切。

Comment:

The Attitude of Life

Attitude is everything people think of “the Bible” where the sentence: as long as it believes that it is willing to believe that there is no impossible.For us, a firm belief is that a hung sailing, and good attitude is the driving force was sailing expedition.Work, some seemingly “impossible” to do something, so long as to maintain a good attitude is important is not thinking “Can I do”, but thinking about “how to do it,” to appear as a difficult task also may be pulled off.This story has been greatly from the ideologically inspired.I think it could only be a good attitude in order to have a better state to restrict themselves to a better work hard, to face different situations, use a good attitude when dealing with to get good results, conversely, can not but fail.Those winners who also use a good attitude when dealing with success and failure so that they can reach the other shore of life the other side of the ideal.In the work before the state of mind is everything.There is no unimportant work, only do not attach importance to the work of people.A different mentality, different achievements in life, what kind of mentality will produce what kind of behavior, to determine different results.Attitude is the attitude of Giga.Character of a person's unique personality and stable performance characteristics, it shows a person's psychological understanding of reality and the corresponding habituation behavior.Attitude is a person's psychological reactions of objective things.Therefore, only a good attitude can in order to have a good job performance.Successfully before the state of mind is everything.“The more slowly, as long as he does not lose goals, is better than people wandering aimlessly go faster.” Thus, life is not always fair;however, the door of hope for everyone is always open.When a person to life and concentrate on one point when, it is possible to make so that their amazing career.Then the basis for success is necessarily a good frame of mind.It is undeniable that, in every one of us psychologically, is the existence of such kind of problems.For example feel too good, learning not to reveal their ignorance;not consider the creation of convenience for others;to attach too much importance personal interests;always want to short-term effects;the lack of subject awareness;will not do any self-criticism.The existence of such a mentality of people, I believe that he will never be successful.On the contrary, those who pursue successful people have opted for precisely the optimization is a positive attitude, and in very good mentality has achieved unexpected success.Such a mentality and state is worth learning and the pursuit of each person, but I can tell you that the mentality of the adjustment and purification, some people are irreplaceable, this is a subjective autonomy of action, not an

objective plus, and passive ideas, other people can not do it guide.Only the right states of mind from the negative idea of coming out, have a positive attitude towards the completion of their goals and work.In other words, “only wanted to contribute, MO on the harvest,” when God will also give you quietly harvest prepared better.The world has countless people.In life, some successful, some fail, some happy, some sad.Some may, some people lose.Why, the same as the beginning of the outcome is different, life's fortune is even more disparity.Indeed, it all depends on your attitude on life.Positive bravely to face, or decadent loss, complaining in broken jar shattered.Really, in the person's life, life can not all be smooth sailing, and his calm.No matter who must have the ability to withstand setbacks? In the immediate difficulties, we should fearlessly go to work, perseverance, not to evade;escape will only make you more and weaker, until the vulnerable.This is why some people can not stand a little frustrated by a failure of despair they do not want to try again, did not dare go down fighting, just because fear of failure again.The boundless world is full of challenges.How to face life, be happy, is sad? Can not allow your life to the decision, nor is it allowed to forward to your fate will be kind, it should be your grasp!

Some people will talk over the failure: “fate, destiny!As already doomed, there is no need to force it adaptable by it.” But whether, but when disaster strikes, but also tightly seated, spoke: “all for life......” No, no, this is only the weak performance, we should regard the attitude of holding their own efforts to go ahead

Indeed, is to change your life, or do you change people's lives, there is up to you.Even if life on the road full of bumps, sadness and grief is always tight as you.But as long as you have always to accompany you to smile, no matter how difficult, how a sad thing to break was in the past, this is the attitude of life!As a matter of fact, the person's life is beautiful, but also very sweet.But often, negative attitude toward life decadent but make your life should have an excellent premature ending, or to give life filled with bitter, so this should be colorful life bleak.An active life does not necessarily make you successful, but a negative attitude toward life is bound to result in making progress, thereby giving up his life!

Everyone has the right to choose the road of life, no matter whether happy, sad matter whether,with the attitude of those who take seriously the life of the road, slowly open up their own little piece of heaven!

第五篇：励志短片（定稿）

励志短片《永不放弃》

看了这部短片之后，请问各位家长您有没有像片中的这位教练一样鼓励自己的孩子，如果有，我恭喜您是为成功的家长，无论是否做到，希望自己孩子以后可以成为栋梁的家长请用自己的掌声来表达对孩子的信心。

放PPT

幼儿练习跆拳道的好处

大家都可能觉得跆拳道踢踢打打，对抗激烈，只适合青少年和成人练习。其实不然，经过实践，有专家表示：让幼儿练习跆拳道好处很多。

具体表现在四个方面：

健体：

跆拳道的健体作用不言而喻。其动作中的各种踢腿、手臂的上格、下截、拉伸等动作，可使幼儿的肌肉和力量得到增强，肌腱、韧带、肌肉的弹性得以提高，从而增强幼儿的体力和柔韧性。

启智：

跆拳道可给大脑许多良好刺激。练习过程不单是骨骼肌肉的收缩，而是空间感知、经验、类型识别等右脑功能的综合发挥，因此非常有利于发展幼儿的空间转换、形体感知等右脑功能，提高了形象思维和创造力。

育心：

跆拳道需要通过做变换方向的动作来明确方位，从而发展了幼儿的空间知觉；此外，孩子们还要主动想办法克服困难，这锻炼了意志，培养了勇敢精神，学会了对人、事、物的正确态度。

知礼：

跆拳道推崇“礼始礼终”的尚武精神，讲究未曾学艺先学礼，未曾习武先习德。通过师幼间的互敬、活动时的敬礼仪式、幼儿之间的相互礼让等，让幼儿理解了“礼”的含义，知道怎样做才是“礼”的表现。